Stock no. B-4300 1/2 Hp CHEMINEER VERTICAL DOWN MIXER Serial number 525557-1 1/2 Hp, 1750 rpm, 230/460 v, 3 ph, Inverter Duty motor Gear reduced, 4.71-1 ratio, 371 rpm shaft speed We make up stainless steel shafts to order. (1) available
Stock no. B-4299 2 Hp LIGHTNIN CLAMP MOUNT AIR POWERED MIXER Model NAR-200, serial no. 7901933 Rated for 2 Hp, gear reduced (1) available
Stock no. B-4297 3 Hp LIGHTNIN CLAMP MOUNT MIXER Model ND-4B, serial no. 7319619 3 Hp, 1740 rpm, 230/460 v, 9.2/4.6 amps, 3 ph Gear reduced. 4-bolt flange mount for shaft Shafts can be made to order (1) available
Stock no. B-4296 30 Hp MODEL 77 O 30 LIGHTNIN DRIVE Serial number 98/8414615601, tagged rebuilt in 2/98 Looks like it has not been used since 30.2-1 ratio, 56 rpm Has 6 inch diameter stub shaft with 12-bolt flange Sell as is or with motor setup Approximately 27 inch x 38 inch x 25 inch […]
Stock no. B-4293 2 Hp PROCHEM AGITATOR DRIVE 226 rpm Model 20VM2S, made by Chemineer serial no. 517346-1 2 Hp, 1735 rpm, 230/460 v, 5.8/2.9 amps, 3 ph 226 rpm shaft speed. Stainless steel stub shaft Round flange mount on square steel plate
Stock no. B-4294 (3) 5 Hp PROCHEM AGITATOR DRIVE 226 rpm Model 20VM2S, made by Chemineer serial no. 517347-1 5 Hp, 1165 rpm, 230/460 v, 13.6/6.8 amps, 3 ph 226 rpm shaft speed. Stainless steel stub shaft Round flange mount on square steel plate (3) similar in stock.
Stock no. B-4288 2 Hp VERTICAL DOWN MIXER with MECHANICAL SEAL Indiana Power Transmission model HOVD-A-56C Serial no. 032698. Ratio 9.813:1 2 Hp Baldor, 1755 rpm, 208-230/460 v, 6-5.8/2.9 amps 8-bolt flange, mechanical seal Came in with 300 gallon reactor E-4461 (1) available
Stock no. B-4277 2 Hp EURODRIVE FLANGE MOUNT GEAR REDUCER 33 rpm 2 Hp, 1720 rpm, 230/460 volt, 6.2/3.1 amps 52.82-1 ratio, 33 rpm output to 2 inch diameter stub shaft 4 bolt flange mount, 9 inch id x 11.5 inch outside diameter. Bolt holes are 10 inch ctr>ctr across (1) available
Stock no. B-4278 (4) 3/4 Hp EURODRIVE FLANGE MOUNT GEAR REDUCER 40 rpm 3/4 Hp, 1700 rpm, 230/460 volt, 2.90/1.45 amps 42.87-1 ratio, 40 rpm output to 1.25 inch diameter stub shaft 4 bolt flange mount (4) available
Stock no B-4275 (2) 1/4 Hp PHILADELPHIA VERTICAL DOWN HIGH SPEED MIXER Type POD, serial number 17P0809 1/4 Hp, 1765 rpm, direct drive, 1-1 ratio. 208-230/460 v, 3 ph 4-bolt mount (2) available
Stock no B-4267 (3) 1/2 Hp VERTICAL DOWN MIXER NETTCO VARIABLE SPEED Nettco model NSGF-050 1/2 Hp, 1750 rpm, 90v dc motor with single phase input Gear reduced with a Minark Motor Master 20000 series speed control (3) available with or without flange mount
Stock no. B-4257 7.5 Hp LIGHTNIN model 16 S 7.5 drive 7.5 Hp, 865 rpm, 230/460 v, 3 ph 14.01-1 ratio, 56 rpm on plate, but should be 61.5 rpm with above motor Will be re-assembled prior to shipping (1) available
Stock No. B-4253 150 Hp LIGHTNIN RIGHT ANGLE DRIVE 84 RPM Model 79 C 150, serial no. 741838 20.8-1 ratio, 84 rpm output Came in with motor starter (1) available
Stock no. B-4242 2 Hp GEAR REDUCED CLAMP MOUNT MIXER Neptune model AG 7.3, serial no. 56532 2 Hp, 1725 rpm, 208-230/460 volt, 3 ph, XP motor, gear reduced takes 1 inch diameter shaft, made up to order (1) available
Stock no. B-4217 .43 Hp Tri-Clamp Mount LIGHTNIN MIXER Model XDDS-43AH, no. 89/388023-02 .43 Hp, 1750/1450 rpm, 208-220/440 volt, 3 ph, 60/50 hz Gear reduced, 350 rpm shaft speed. Stainless steel stub shaft with 4-bolt shaft flange Mechanical seal, 6 inch tri-clamp mount (1) available
Stock no. B-4213 1 Hp LIGHTNIN VERTICAL DOWN MIXER model XLQ-100 Serial no. 85/264308-02 1 Hp, 1140/950 rpm, 60/50 Hz, 208-220/440 volt Shaft speed approximately 228 rpm @60 Hz 4-bolt mount Can make up shaft and blades or prop to order
Stock no. B-4214 30 Hp CHEMINEER Model 6HTA-30 RIGHT ANGLE DRIVE Serial no. 562255-1 68 rpm with 1800 rpm input, rated for 30 Hp Sell with or without motor setup Shafts and blades made up to order (1) available
Stock no. B-4207 1/2 Hp JWI CLAMP MOUNT MIXER Model JL50, gear reduced 1/2 Hp, 1725 rpm, 230/460 volt, 3 ph Approximately 350 rpm output Takes bolt on shaft which we can make to order (1) available
Stock no. B-3277 2 inch GREERCO STAINLESS STEEL INLINE MIXER Model 2PLM, missing plate Approximate capacity 6 to 11 gpm 2.5 inch tri-clamp fittings. 1.75 inch rotor diameter 2 hp, 230/460 v, 3ph, 60hz. (1) available
Stock no. B-3867 (4) 1 Hp CHEMINEER CLAMP MOUNT MIXER XP 1750 rpm, 230/460 v, 3 ph, XP motor, 5.21-1 ratio 335 rpm shaft speed With stainless steel shaft and prop (4) available.
Stock no. B-4189 1.5 Hp LIGHTNIN VERTICAL DOWN MIXER FLANGE MOUNT Model 1S110, no. 102058, year 2002, made in China Rated for 1.27 Kw @ 440 volt, 60 Hz (1.5 Hp), 840 rpm 1.1 Kw 220/380 volt, 50 Hz, 700 rpm 150 rpm shaft output speed listed on plate Stainless steel contacts with 14 inch […]
Stock no. B-4183 LIGHTNIN CLAMP MOUNT LAB MIXER STIRRER 1/15 Hp, 115 volt, 1600 rpm. Model S1U05T Stainless steel shaft, 18 inch to chuck, 22 inch to bottom of mixer With 3.5 inch A310 type blade Optional stainless steel stand available at additional charge (1) available
Stock no. B-4178 7.5 HP LIGHTNIN 74 C 7.5 FLANGE MOUNT DRIVE 38.35 ratio Model 74 C 7.5, 38.35-1 ratio, 48 rpm output with 1750 rpm in Stainless steel faced flange mount and stainless steel stub shaft Packed seal Will sell with or without motor setup (1) available
Stock Number: B-4177 40 HP LIGHTNIN RIGHT ANGLE DRIVE MIXER 76 Q 40, 20.2 ratio Mfg. Lightnin Model 76 Q 40, no. 7010806 20.2-1 ratio, 58 rpm with current 1185 rpm motor 460 volt, 3 ph (1) available
Stock no B-3674 (2) 2 Hp CHEMINEER 2HTD-2 RIGHT ANGLE DRIVE 56 rpm Model 2HTD-2 2 Hp, 1725 rpm, 208- 230/460 v, 3 ph Rated for 56 rpm with 1800 rpm input Shaft and blades available at additional charge (2) available
Stock no B-4118 3 Hp CHEMINEER HTA-3 RIGHT ANGLE DRIVE 68 rpm Model HTA-3, no. 564532-1 Rated for 468 rpm with 1200 rpm input Will sell with or without a motor setup Shaft and blades are optional (1) available
Stock no. B-4028 (2) 25 Hp BRIDGE MOUNT LIGHTNIN DRIVE 17.1-1 ratio Model 318 7TELB 252 Rated for 25 Hp with 1750 rpm input, 17-1 ratio, 102 rpm output Currently has a 2 speed motor, 1740/960 rpm in, 100/50 rpm out Motor is 550 volts, 3 phase, but we can change (2) available
Stock Number: B-3529 10 HP LIGHTNIN RIGHT ANGLE DRIVE 84 rpm output Mfg. Lightnin Model 972×062, serial no. 8420571601 Ratio 20.8, 84 rpm output (1) available
Stock no. B-4174 3 Hp STAINLESS STEEL SWEEP AGITATOR DRIVE Manufactured by Shar, more info to follow 3 Hp, 1170 rpm, 208-230/460 volt, 3 ph Gear reduced Came off a 250 gallon tank rated for 30 psi, 40 inch id x 48 inch straight side No longer with tank top in picture (1) available
Stock no. B-4173 (2) 1/3 Hp LIGHTNIN CLAMP MOUNT MIXER Model ND1 .33 Hp, 1725 rpm, 230/460 volt, 3 ph Gear reduced, 5/8 inch chuck for shaft Stainless steel shaft made to order Will furnish with clamp mount or swivel bolt mount Will test, clean, and repaint prior to shipping. (2) available
Stock no. B-4171 3/4 Hp LIGHTNIN CLAMP MOUNT MIXER Model ND2A, no. 7212546 .75 Hp, 1725 rpm, 115/230 volt, 1 ph Gear reduced, 5/8 inch chuck for shaft Stainless steel shaft made to order Will furnish with clamp mount or swivel bolt mount Will test, clean, and repaint prior to shipping. (1) available
Stock no. B-4158 1 Hp LIGHTNIN AIR POWERED CLAMP MOUNT MIXER Model X5P100A, no. R05435579-03 Rated for 1 Hp air powered (1) available
Stock no B-4159 10 Hp CHEMINEER RIGHT ANGLE DRIVE Model 4-HTD-10, no. 1-938824-1 Rated for 45 rpm with 1200 rpm input Will sell with or without a motor setup Shaft and blades are optional (1) available
Stock no. B-4160 1/3 Hp LIGHTNIN CLAMP MOUNT MIXER Model X5P33, year 2017 .33 Hp, 1725 rpm, 208-230/460 v, 3 ph Gear reduced. Takes 3/4 inch diameter shaft (1) available, other 2 in picture have been sold
Stock no. B-4163 1 Hp LIGHTNIN FLANGE MOUNT MIXER XP Model N33G-100, no. 7315427 1 Hp, 1745 rpm, 230/460 v, 3 ph, for hazardous locations Gear reduced, 350 rpm shaft speed 1.5 inch diameter shaft (1) available
Stock no. B-4164 .65 Hp LIGHTNIN FLANGE MOUNT MIXER with MECHANICAL SEAL Model XJDS-65, no. 88/345122 .65 Hp, 1140/960 rpm 208-230/460 v, 60/50 hz, 3 ph XP for hazardous locations 1.25 inch diameter shaft, approx. 288 rpm output 9 inch stainless flange face, 11 inch outside diameter (1) available
Stock no. B-4147 5 Hp VERTICAL DOWN MIXER by EKATO Model EM2040, no. 66311-10, year 2004 5 hp motor with stainless steel housing 1750 rpm, 208-230/460 volt, 3 ph, 60 hz Has dust seal, rated for 14.5 psi @ 212 deg. F Takes a 1.5 inch diameter shaft. 4-bolt flange mount With or without stainless […]
Stock no. B-4148 3 Hp SIDE ENTERING AGITATOR MIX PRO Model 12VSM rated for 345 rpm with 1800 rpm input 1.25 inch diameter x 15 inch stainless steel shaft 17 inch prop Sell with or without motor setup Looks unused! (1) available
Stock no. B-4152 15 Hp CHEMINEER RIGHT ANGLE DRIVE 45 rpm Model 23HTP-15, no. 577435-1 Rated for 45 rpm with 1800 rpm input Will sell as it is or with a motor setup Shaft and blades are optional as well (1) available
Stock no. B-4154 (2) 1/3 Hp AIR POWERED CLAMP MOUNT MIXER LIGHTNIN Model XJA 33 rated for 1/3 Hp Air powered, gear reduced With or without a stainless steel shaft and prop (2) available plus other similar mixers
Stock no. B-4155 1 Hp AIR POWERED CLAMP MOUNT MIXER LIGHTNIN Model NAG100, rated for 1 Hp Air powered, gear reduced. With or without stainless steel shaft shaft and prop
Stock no. B-4156 1/2 Hp AIR POWERED CLAMP MOUNT MIXER JWI Model JLA50 rated for 1/2 Hp With or without a stainless steel shaft and prop (1) available
Stock no. B-4149 3 Kw (4 Hp) FLANGE MOUNT DRIVE AGITATOR Wuxi Top Mixing Equipment Ltd Serial no. 256841, model TOPF58-1/3-12.26 3 Kw (4.02 Hp), approx. 1750 rpm, 480 v, 3ph 12.26-1 ratio gear reduced, 143 rpm shaft speed 2.5 inch diameter x 104 inch stainless steel shaft Flange/bridge mount Originally mounted on 2,000 gallon […]
Stock no. B-4141 (2) .43 Hp LIGHTNIN CLAMP MOUNT MIXER Model XJ43 .43 Hp, 1725 rpm, 208-230/460 v, 3ph Has custom quick disconnect for shaft Will furnish with clamp mount or swivel bolt mount (2) available
Stock no. B-4146 3 Hp CHEMINEER 1-HTA-3 FLANGE MOUNT DRIVE 84 rpm Serial no. 1-9560-11 3 Hp, 1765 rpm, 230/460 v, 3 ph Rated for 84 rpm output with 1800 rpm input Stainless steel faced mounting flange, packed seal (1) available
Stock no. B-2752 25 HP LIGHTNIN FLANGE MOUNT DRIVE 76 C 25 Model 76 C 25, 25-1 ratio, 68 rpm output 16-bolt flange mount. 45 inch tall Will sell with or without motor setup (1) available
Stock no. B-4134 (2) 1/2 Hp CHEMINEER CLAMP MOUNT MIXER model 3JTC-0.50 1/2 Hp, 1750 rpm, 115/230 volt, 3 ph, XP Direct drive. Takes a 1 inch diameter shaft included with a single prop (2) available
Stock no. B-4127 7.5 Hp CHEMINEER RIGHT ANGLE DRIVE Model 2 HT, no. ICM 2524-96 7.5 Hp, 1725 rpm input Labeled with 060 gears. Output speed and ratio to be determined (1) available
Stock no. B-4126 (2) 30 Hp CHEMINEER RIGHT ANGLE DRIVE Model 4 HTD-30, serial no. 501285 30 Hp, 1760 rpm input. Labeled with 020 gears Output ratio and speed to be verified (2) similar available
Stock no. B-4128 10 Hp CHEMINEER RIGHT ANGLE DRIVE FLANGE MOUNT w/ SEAL Model 3 HTN-10, serial no. 1-95630-13, 20-1 ratio, 88 rpm output 10 Hp, 1750 rpm, 230/460 v, 3 ph, 60 hz Stainless steel faced flange mount, mechanical seal 54 inch overall height (1) available
Stock no. B-4129 60 Hp LIGHTNIN RIGHT ANGLE DRIVE Model SX-77-Q-60, no. 97E8923602 20.54-1 ratio, tagged 57.7 rpm output (with 1185 rpm input) Has stub shaft. Currently without a motor (1) available
Stock no. B-4099 5 Hp LIGHTNIN 71 Q 5 RIGHT ANGLE DRIVE 188 rpm Model 71 Q 5, no. 7701126 5 Hp, 1750 rpm, 230/460 v, 3 ph, XP 9.33:1 ratio, 188 rpm shaft speed (1) available
Stock no. B-4107 1/3 hp CLAMP MOUNT MIXER 115 208 230 volt EASTERN model RH-2, serial no. 023284 .33 hp, 1725 rpm Baldor, gear reduced 115/208/230 volt, 1 ph, 60 hz, 6/3.2-3 amp Includes stainless steel shaft made to order and prop (1) available
Stock no. B-3842 5 Hp CHEMINEER 84 rpm RIGHT ANGLE DRIVE Model 2HTA-5, 21.4:1 ratio, 84 rpm with 1800 rpm input Unused. With or without a motor setup. (1) available
Stock no. B-4093 1.5 Hp CHEMINEER VERTICAL DOWN MIXER with motor UNUSED Model 3BTNS-15, no. 1-97411-4 Includes motor not pictured, 1.5 Hp, 1780 rpm, 230/460 v, 3ph Gear reduced with Hub City gear box model 254 5/1, style 0010 UNUSED! In crate with original packing slip (1) available
Stock no. B-4097 3 Hp LIGHTNIN FLANGE MOUNT DRIVE 72 C 3 33 to 100 rpm Model 72 C 3, no. 6915645, 16.95:1 ratio, 33 to 100 rpm shaft speed with variable speed pulley setup 3 Hp, 1750 rpm, 230/460 v, 3 ph Stainless steel faced flange mount (1) available
Stock no. B-4081 1.5 HP CHEMINEER 1HTNS-1.5 RIGHT ANGLE DRIVE 100 RPM No. 2-D5393-1, 18:1 ratio, 100 rpm output with 1800 rpm input Sell with or without motor setup We can make shafts to order (1) available
Stock no. B-4080 5 HP LIGHTNIN 72 C 5 RIGHT ANGLE DRIVE 84 RPM No. 92746956, rebuilt by Lightnin 10/92 21.1 ratio, 84 rpm output with 1750 rpm input Sell with or without a motor setup Shafts and blades are optional (1) available
Stock no. B-3678 5 Hp PHILADELPHIA RIGHT ANGLE DRIVE MT-02 100 RPM Size MT-02, serial no. 96BBH0725 17.5-1 ratio, 100 rpm output 5 Hp, 1730 rpm, 230/460 v, 3ph Flange mount (1) available
Stock no. B-4063 20 Hp LIGHTNIN DRIVE 84 S 20VM to 155 RPM Serial no. 7905550, 11.3-1 ratio, model 84 S 20VM Originally with variable speed, 55 to 155 rpm output Will supply with a single speed 20 Hp motor (1) available
Stock no. B-4066 1.5 Hp LIGHTNIN RIGHT ANGLE DRIVE 71 C 1.5VM No. 77173867, 25.68-1 ratio, variable speed pulley, 15 to 45 rpm output 1.5 Hp, 1140 rpm, 230/460 v, 3ph (1) available
Stock no. B-3994 15 Hp LIGHTNIN RIGHT ANGLE DRIVE SX 74 Q 15 LIGHTNIN serial no.9052995501, model SX74 Q 15 15 Hp, 1750 rpm/6.6 Hp, 1185 rpm 2 speed motor 68/45 rpm shaft speed 25.6-1 ratio 460 volt, 3 ph, 60 hz (1) available
Stock no. B-4019 2 to 3 Hp RIGHT ANGLE DRIVE PRO QUIP Model 3ZES50B, s/n & w/o 11031 With 2 Hp, 860 rpm motor. drive rated for 3 Hp 50-1 ratio, 17.20 rpm shaft with 860 rpm input. 35 @ 1750 in Electrical data 230/460 volt, 3ph (1) available
Stock no. B-4056 LIGHTNIN LAB STIRRER CLAMP MOUNT MIXER Model 11, no. 7807633 Motor plate needs cleaning, 115 volt input Has Drill Type chuck for shaft (1) available
Stock no. B-4049 .30 Hp LIGHTNIN VERTICAL DOWN MIXER 575 volt Model XJSS-30, no. R02402023-01, CW rotation .30 Hp, 1725 rpm, 575 v, 3 ph, 60 hz Gear reduced. 4-bolt mount mount. 4″ od with 4-bolt shaft mount, stainless steel Can make shaft to order. We may be able to change motor to a different […]
Stock no. B-4053 1/3 Hp LIGHTNIN 115 VOLT CLAMP MOUNT MIXER Model XJ-30, no. 84/203069 115 volt single phase, 1725 rpm, gear reduced Includes 5/8″ diameter stainless steel shaft & prop (2) similar available
Stock no. B-4054 1/2 Hp LIGHTNIN VARIABLE SPEED CLAMP MOUNT MIXER Model X1P50, no. 903414895-0 1/2 Hp, 1750 rpm, 90 v dc with 120 v input Gear reduced with 3/4″ diameter stainless steel shaft (1) available
Stock no B-4017 2 Hp LIGHTNIN VERTICAL DOWN MIXER XP Model NLDG200, no. 700317 2 Hp, 2 speed motor, 1765 /880 rpm, 480 volt, 3 ph XP Gear reduced, 350 rpm/175 rpm shaft speed Flange mount for shaft. Optional angle mount attached (1) available, other similar mixers available
Stock no. B-3999 1/3 Hp LIGHTNIN VEKTOR CLAMP MOUNT MIXER No. 94B87609-10 .33 Hp, 1750 rpm, 208-230/460 volt, 3ph Gear reduced. Takes a 1″ diameter shaft. Stainless steel shaft and prop sized to order. (1) available
Stock no. B-3997 3 Hp CHEMINEER RIGHT ANGLE DRIVE Model 1-HTD-3, s/n 2-46708-2 3 Hp, 1750 rpm motor, 208-230/460 volt, 3 ph 100 rpm output. Optional tall base available (1) available
Stock no. B-4032 (4) 2 Hp PRO QUIP RIGHT ANGLE DRIVE Model JLX2QP, plate needs cleaning for serial number 2 Hp, 230/460 volt, 3 ph, 88 rpm shaft speed, 20:1 ratio (4) available
Stock no. B-4035 1 Hp LIGHTNIN CLAMP MOUNT MIXER XP Model ND3, no. 553640 1 Hp, 1760 rpm, 208-230/460 v, 3ph, xp Gear reduced, 350 rpm shaft Flange for shaft mount. Sell with or without shaft and prop (1) available
Stock no. B-4034 1.5 Hp LIGHTNIN CLAMP MOUNT MIXER XP Model ND4, no. 89/386693 1.5 Hp, 1760 rpm, 230/460 v, 3ph, xp Gear reduced, 350 rpm shaft Flange for shaft mount. Sell with or without shaft and prop (1) available
Stock no. B-3241 2 Hp RIGHT ANGLE DRIVE Manufacturer BOWERS MACHINE CO LTD Serial no. F-1530, model 40 OT Radicon gear box approx. 2 Hp, 3ph motor will supply updated motor with choice of voltage Came in mounted on a 500 gallon tank (1) available
Stock no. B-3979 1/2 Hp SINGLE PHASE TANK MOUNT MIXER .50 hp, 1 ph tank mount mixer vertical mount 115/220 volt, 1 ph, 7.4-3.7 amp, 1725 rpm, 1/2 Hp gear reduced Includes stainless steel shaft and prop (1) available
Stock: B-3972 1/4 Hp AIR POWERED CLAMP MOUNT MIXER LIGHTNIN model NAR 25, serial no. 6710233 .25 hp mixer, Gast air motor clamp mount with stainless steel shaft and prop (1) available
Stock no. B-3993 10 gallon J H DAY STAINLESS STEEL PONY MIXER Compares to model 1A, serial no. 84314 208-220/440 v, digital speed control Stainless steel tank and blades Other similar units available
Stock no. B-3992 2 inch SPECO STAINLESS STEEL INLINE MIXER Model 2TSPL, s/n 79-10635 o/a 24 inch x 46 inch x 46 inch including cart w/(4)wheels. 2 inch x 2 inch in and out w/ reducer flange to 1 inch 3 hp, 1735 rpm input, variable speed 420-4200 rpm output 230/460v, 3ph, 60hz. (1) available
Stock no. B-1617 1/2 Hp SHAR VERTICAL DOWN MIXER Serial no. 12103794 1/2 Hp, 1750 rpm, 3 ph motor Gear reduced to 85 rpm shaft speed Currently mounted on tank lid (1) available
Stock no. B-1603 1 Hp VERTICAL DOWN LIGHTNIN MIXER with 4-bolt base Model XLQ-100H Gear reduced to 44 rpm shaft speed 1 Hp, 1140 rpm, 230/460 v, 3 ph (1) available
Stock no. B-3619 4.5 inch 4-BLADE STAINLESS STEEL TURBINE AGITATOR HUBS 45 degree pitch paddle, keyed We can also make up straight blades to order. (3) available
Stock no. B-3115 SIZE 4 PFAUDLER AGITATOR DRIVE 15-1 ratio Model FDWV-50410-BJD, no. 4-00064-P Rated to 8.3 Hp Will sell with or without motor setup (1) available
Stock no. B-3982 SIZE 4 PFAUDLER AGITATOR DRIVE 15-1 ratio Model DWV-50410-BJD, no. 92166067-001 Rated to 8.3 Hp Sell with or without motor setup (1) available
Stock no. B-1555 125 Hp PFAUDLER DRIVE AGITATOR Size 130-TVV-T, no. M-7971 (100RH-TS) Rated for 187.5 Hp, 15.3-1 ratio, 110 rpm output Originally with a 125 Hp, 1750 rpm motor (selling drive only) (1) available
Stock no. B-3971 3 Hp LIGHTNIN RIGHT ANGLE DRIVE 68 rpm Model 943X022, Serial no. 8197465601 25.6-1 ratio, 68 rpm output 3 Hp, 1750 rpm, 230/460 volt, 3ph (1) available
Stock no. B-3957 1/2 Hp EASTERN VERTICAL DOWN MIXER FRG 3C 949.02 1/2 Hp, 1725 rpm, 230/460 v, 3ph Gear reduced (1) available
Stock no. B-3956 2 hp CHEMINEER 1 GTN 2 VERTICAL DOWN DRIVE S/n 552624-2 1725 rpm input, 155 shaft speed 230/460 v, 3ph (1) available
Stock no. B-3955 3 hp CHEMINEER 2 GTN 3 VERTICAL DOWN DRIVE 1750 rpm input, 100 rpm shaft speed 230/460 v, 3ph Came in with stock no. E-4127, 1450 gallon reactor (1) available
Stock no. B-3950 1.5 hp LIGHTNIN XLQ-100D VERTICAL DOWN MIXER S/n 88/A28233 1.5 Hp, 1725 rpm, 208-230/460 v, 3ph Gear reduced, flange mount shaft (1) available
Stock no. B-4287 2 liter STAINLESS STEEL VACUUM PLANETARY MIXER DISPERSER Guangzhou Huiheng Mechanical And Electrical Equipment Co., Ltd DLH 2, 2004-109, Chinese made Jacketed Stainless steel vessel is 6.5 inch x 6.5 inch flat bottom, lid with gasket (2) 2 inch sight glass + light, (2) .25 inch vent + vacuum (2) 3/8 inch […]
Stock no. B-3908 (3) 1/4 Hp VERTICAL DOWN GEAR REDUCED MIXER UET Excel Ram 20, yr 2005 1/4 Hp, 1750 rpm, 208-230/460v, 3ph 350 rpm shaft speed, 4 bolt mount (3) available
Stock no. B-3882 (2) 2 Hp CHEMINEER VERTICAL DOWN GEAR REDUCED MIXER 2 Hp motor, 1750 rpm, 208-230/460 v, 3ph (2) available
Stock no. B-3900 (5) 2 Hp BRAWN VERTICAL DOWN MIXER GEAR REDUCED XP Model BGMF200SP 2 Hp, 230/460v, 3ph, xp Currently mounted on a 22 inch stainless steel lid for a tote tank/IBC or drum (5) available
Stock no. B-3948 (2) 10 Hp FALK RIGHT ANGLE DRIVE model 357AFXD3A2 187.5 ratio, 9.3 rpm output Rated for 10 Hp and currently has a 15 Hp motor 1750 rpm, 230/460v, 3ph (2) available
Stock no. B-3946 1 Hp CHEMINEER CLAMP MOUNT MIXER Model X Press Portable, 1 Hp, 1750 rpm 230/460v, 3ph 5.21 gear ratio , 336 rpm max shaft speed Comes with stainless steel shaft and prop (1) available
Stock no. B-3942 1 Hp AIR MIXER with SPEED CONTROL and TRI-POD MOUNT Approx. 1 Hp by physical size of mixer, looks like a Gast mixer Automatic and manual speed controls with forward and reverse Adjustable tri-pod mount for top of tank With regulator and filter (1) available
Stock no. B-3939 Size 4 Pfaudler agitator drive model DW-50410-BJD No. 4-D0568P Rated for 10.50 Hp, 10-1 ratio Sell with or without motor setup (1) available
Stock no. B-3922 (2) Lightnin model NLDG-33 gear reduced vertical down mixer 1/3 Hp, 1725 rpm > 350 rpm shaft speed, 115v, 1 ph 4-bolt mount. Takes 5/8″ diameter shaft Please note that we test, clean, and paint our mixers before shipping. (2) available
Stock no. B-3757 Lightnin 1/3 Hp high speed clamp mount mixer Model NS-1, no. 80/801226 1/3 Hp, 1725 rpm, 115v, 1ph (1) available
Stock no. B-3771 Pro Quip 3 Hp right angle drive mixer Model 300 JLX10P, no. 16007 Rated for 3 Hp, 10-1 ratio Sell with or without a motor (1) available
Stock no. B-3768 1/2 Hp NEPTUNE CLAMP MOUNT MIXER Neptune 1/2 Hp clamp mount mixer model D-1.7, no. 117713 Direst drive, with 90 v dc motor. Requires 115 v speed control not included (1) available
Stock no. B-3780 Lightnin 1/4 Hp rated air powered clamp mount mixer Model NAR 25, high speed direct (1) this model, more similar high speed Lightnin mixers available
Stock no. B-3779 2 Hp STAINLESS STEEL INLINE MIXER EMULSIFIER ROSS Ross series 300 stainless steel inline mixer No plate, but compares with a series 300 Ross inline mixer emulsifier Tagged MCC 23-5 3-CD, 127-305-48 Blender Coating Prep 2 Hp, 3450 rpm, 460v, 3ph, xp 18 inch diameter x 25.75 inch with 14 inch cone […]
Stock no. B-3848 (3) 3 hp PRO QUIP RIGHT ANGLE DRIVE 10:1 ratio 175 rpm Pro Quip model 300JLX10P, 3 Hp right angle drive 3 Hp, 1750 rpm, 230/460 volt 3 ph Gear reduced, 10-1 ratio, 175 rpm max output (3) available and ready to go. Shafts can be made to order.
Stock no. B-3838 Lightnin 10 Hp right angle drive agitator Model 74-Q-10 10 Hp, 1750 rpm, 3 phase (choice of voltage) ratio 25.6, 68 rpm output 3 inch diameter x 5 ft stainless steel 8-bolt stub shaft (1) available
Stock no. B-3843 Lightnin 50 Hp Right Angle Drive Agitator Model 76-S-50, 21.1 ratio, 10 to 84 rpm Rated for 50 Hp. Flange mount with mechanical seal Currently setup with a hydraulic motor, but can be converted to electric. (1)available
Stock no. B-3756 Chemineer 1.5 Hp gear reduced mixer No. 5544072 1.5 Hp, 1725/1450 rpm, 208-230/460v, 3ph (1)available
Stock no. B-3755 (2) 3 Hp PRO QUIP RIGHT ANGLE DRIVE Pro Quip model 300 JH X 20P 3 Hp, 1755 rpm, 230/460v, 3ph 19.67 ratio, 88 rpm output (2)available
Stock no. B-3808 2 hp SANITARY STAINLESS STEEL TRI-BLENDER MIXER Model no. 2116MD B40, s/n 03014 Manufacturer TRI-CLOVER Division Of Alfa Laval Sanitary stainless steel 316 Tri-clamp 2″ for powders, 1.5″ liquid in & out Top feed cone included** Motor 2.5 hp 3600 rpm 3 ph, 230/460 volt,3.9 amp (1) available
Stock no. B-3738 30 hp LIGHTNIN RIGHT ANGLE DRIVE 68 rpm Model 76 Q 30, serial no. 7519331 Manufacturer LIGHTNIN Motor 30 hp, 1770 rpm, Drive 25 ratio, 68 output Electrical data 575 volt, 29 amp, 3 ph Can swap out motor or sell without
Stock no. B-3736 (2) 25 hp LIGHTNIN RIGHT ANGLE DRIVE 84 rpm LIGHTNIN Model 75 Q 25, serial no. 7519333 Drive 20.2 ratio, 84 hp output rpm with 1750 input Will sell with or without a motor Optional shaft can be made to order (2) available
Stock no. B-3735 20 hp LIGHTNIN RIGHT ANGLE DRIVE 100 rpm Model/serial no. 74 Q 20 s/n 740365 Manufacturer LIGHTNIN 20 hp, 1765 rpm 16.6 ratio, 100 hp output rpm, 575 volt, 3 ph, 20 amp. Can sell with different motor or without.
Stock no. B-3731 (3) 25 Hp CHEMINEER RIGHT ANGLE DRIVE 100 rpm Model 4-HTD-25, serial no. 1 928373-6 Manufacturer Chemineer Inc. with or without motor added Rated for 25 Hp, 1200 Rpm input Drive 100 rpm output (3) available
Stock no. B-3802 1.5 gallon HENSCHEL PRODEX HIGH INTENSITY MIXER HENSCHEL PRODEX Model FM 2 stainless steel contacts, 8.5 inch inside diameter x 8 inch deep bowl 3 inch bottom out, (4) 3/4 inch jacket in-out Priced reconditioned** Motor 2 kw,(2.6 Hp) 3420 rpm Electrical data 3 ph
Stock no. B-3803(2) 1/4 Hp LIGHTNIN VERTICAL DOWN MIXER FLANGE MOUNT Model Vektor v5c18n, serial no. R9971375200501 Manufacturer LIGHTNIN Stainless steel flange mount. LOOKS UNUSED** Has polished shaft + prop Motor .25 hp, 1750 rpm gear reduced, 3 ph, 230/460 volt (2) available
Stock no. B-3831 3.5 hp LIGHTNIN CLAMP MOUNT MIXER Model/serial no. nd 4b 92/A78621 Manufacturer LIGHTNIN Motor 3.5 hp, 1725/1450 rpm Electrical data 220/440 volt,10.6/5.3 amp, 3 ph
Stock No. B-3792 Lightnin 1.17 Hp clamp mount mixer high speed Model XD117, direct drive 1.17 Hp, 1740 rpm, 230/460 v, 3ph, 6.6/3.3 amps (2) available
Stock No. B-3791 Lightnin 3/4 Hp clamp mount mixer Model XD75VM, direct drive 3/4 Hp, 1725 rpm, 208-220/440 v, 3 ph Originally with dc motor pictured, changed to 3 phase motor (1)available
Stock Number: B-3204 60 QUART UNIVEX DOUGH MIXER Mfg. Univex Model M-60, no. 645165 3 Hp, 1725 rpm, 208/240 v, 3ph, 7 amp Stainless steel bowl, with beater and guard (1) available
Stock Number: B-2978 140 QUART DOUGH MIXER AMF UNION GLEN Mfg. AMF Union Glen-Mixer model 74-47, no 681 Variable speed 70-370 rpm Manual crank bowl lift 2 Hp, 1750 rpm, 208-220/440v, 5.9/2.6 amp Includes bowl, no attachments. (1) available
Stock Number: B-3234 15 HP SCHOLD SLOW SPEED DISPERSER MIXER Mfg. Schold Machine Co. Variable speed, 48 to 160 rpm shaft 3 inch x 44 inch carbon steel shaft Bow-tie 3-blade mixing 15 Hp,220/440 v, 3ph Has crack in lift piston. Selling “AS IS” (1) available
Stock Number: B-1511 15 HP HOCKMEYER DISPERSER LOW SPEED MIXPERSER Mfg. Hockmeyer Equipment Model HVR-15M, s/n 78106, Heavy Duty Mixperser 15 Hp, 1750 rpm motor, currently 575 v 2.25 x 51 inch Carbon steel shaft, 250 rpm max (2) 30 inch ss paddle type blades (1) available
Stock Number: B-3327 Mfg. Lightnin Vektor model VST18N 1/4 Hp, 1725 rpm, 230/460v, 3ph Flange mount with stainless steel face Sell with or without shaft and prop (1) available
Stock Number: B-3563 1/4 Hp LIGHTNIN VEKTOR CLAMP MOUNT MIXER high speed Mfg. Lightnin Vektor model V1P18N 1/4 Hp, 1725 rpm, 230/460 v, 3ph High speed stainless steel shaft made to order and prop included Several similar mixers available!! (1) available
Stock Number: B-2276 1/4 HP LIGHTNIN VEKTOR CLAMP MOUNT MIXER Mfg. Lightnin Vektor model V6P18 1/4 Hp, 1740 rpm, 208-230/460 v, 3ph gear reduced stainless steel shaft made to order and prop included (1) available
Stock Number: B-3564 (2) .33 HP LIGHTNIN VEKTOR CLAMP MOUNT MIXER 115/230 v Mfg. Lightnin Vektor model V5P25 1/3 Hp, 115/230 v, 1 ph gear reduced stainless steel shaft made to order and prop included (2) available
Stock Number: B-3349 1/2 HP VERTICAL DOWN LIGHTNIN MIXER Mfg. Lightnin Vektor model VIT37 1/2 Hp, 1720 rpm input, high speed, 230/460v, 3ph 10 inch flange mount with mechanical seal for 1″ diameter shaft (1) available
Stock Number: B-3718 Lightnin .65 Hp clamp mount mixer 1750 rpm, 208-220/440v, 3ph motor Need to verify model number High speed model (1) available
Stock Number: B-3628 1 HP LIGHTNIN CLAMP MOUNT MIXER Mfg. Lightnin Model XJ 87 Originally with .87 Hp, now 1 Hp, 230/460 volt 3ph Gear reduced, approx. 350 rpm output bolt on flange for shaft. Shafts available, made to order (1) available
Stock Number: B-2856 Mfg. Lightnin Model XLSS 100A, no. 91/A56743 Gear reduced, estimated shaft speed 690 at 3450 rpm 1 Hp, 3450/2050 rpm, 208-230/460v, 3ph, xp 4 bolt mount, 6-bolt flange for shaft mount (1) available
Stock Number: B-3393 Mfg. Pro Quip Model 1 YEX 44 1 Hp, 1745 rpm, 230/460v, 3ph 44-1 ratio, 37 rpm output (1) available
Stock Number: B-3422 Mfg. Lightnin Model 72 S 1 5:1 atio, 350 rpm output 1 Hp, 1745 rpm, 230/460v, 3ph motor (1) available
Stock Number: B-2901 Mfg. Nettco Corp Model NSGF-100 1 Hp, 1140 rpm, 230/460v, 3ph gear reduced (1) available
Stock Number: B-3565 1.5 HP CHEMINEER RIGHT ANGLE DRIVE MODEL 1 HTN-1.5 Model 1 HTN-1.5, no. 2-A4443-1 Rated fot 1.5 Hp with 1750 rpm input, 100 rpm output Possibly UNUSED! (1) available
Stock Number: B-3684 1.74 Hp Lightnin vertical down mixer gear reduced 1.74 Hp, 230/460 v, UL listed Group I Hazards Model XJSS-174, serial no. 92-B00685 gear reduced, 350 rpm output (1) available
Stock Number: B-1872 2 HP LIGHTNIN RIGHT ANGLE DRIVE 31.5-1 ratio Mfg. Lightnin Model 72 C 2 31.5 ratio, 37 rpm output with 1175 input 2 Hp, 1175 rpm, 480 v, 3ph (1) available
Stock Number: C-2363 (2) 7.5 hp HOBART STAINLESS STEEL FOOD MIXER GRINDER Mfg. Hobart Model 4346 7.5 Hp, 1725 rpm, 3ph, 460 volt 4 inch outlet, Foot switch Missing feed screw and attachments (2) available, Second one is 200 volt, stock no. C-2247
Stock Number: B-1751 Mfg. J. H. DAY, INC. Model CD-18, s/n 310 (2)Vari-drive 3 HP,(1)1 HP, 230/460V, 3PH, 60HZ Stainless steel Rated for 18 cu. ft. / hr. For liquids and powders Double rotating discs w/dispersion bars (1) available
Stock Number: B-3273 (4) 3 HP RIGHT ANGLE DRIVE LIGHTNIN 81 S 3 MECHANICAL SEAL Mfg. Lightnin Model 81-S-3 3 Hp, 1725 rpm, 230/460 v, 3ph, 60hz 21.1 ratio, 82.9 rpm output Mechanical seal (4) available
Stock Number: B-1944 3 HP LIGHTNIN RIGHT ANGLE DRIVE 82 C 3 Mfg. Lightnin Model 82-C-3 3 Hp, 1750 rpm, 480v, 3ph 21.1 ratio, 84 rpm shaft speed (1) available
Stock Number: B-3668 Mfg. Lightnin Model XJ 350, no. 87/345195-02 3.5 Hp, 1750 rpm, 230/460v, XP 350 rpm shaft speed, takes flange mount shaft (1) available
Stock Number: B-3531 SIZE 4 PFAUDLER AGITATOR DRIVE Mfg. Pfaudler Size 4.000, model DWV50410BJD, no. 88112739-001 Originally with 7.5 Hp, 1750 rpm, 230/460v, 3ph 15-1 ratio, rated for 8.30 Hp (1) available
Stock Number: B-2912 Mfg. Pfaudler Size 5.00, model FDWV-50510-BJD Rated for 25.8 Hp 10-1 ratio No seal! (1) available
Stock Number: B-3359 Mfg. Lightnin Model 227 TEC 52 5 Hp, 1760 rpm, 230/460v, 3ph 38.4-1 ratio, 45 rpm output (1) available
Stock Number: B-1820 Mfg. Pfaudler Model 5TWV, FHV-45985C, 5777 10-1 ratio, rated for 25.8 Hp (1) available
Stock Number: B-2861 Mfg. Chemineer Modeflex Turbine Agitator model MAJ-50-33 5 Hp, 1750 rpm, 230/460v, 3ph 31.4 ratio, 56 rpm output (1) available
Stock Number: B-3507 (2) Mfg. Falk Division of Sunstrand Model 300MDXDF3A 5 Hp, 1750 rpm, 230/460v, 3ph 39.65 ratio, 44 rpm output, CW (2) available
Stock Number: B-3588 5 HP LIGHTNIN RIGHT ANGLE DRIVE Mfg. Lightnin Model 71 S 5 Rated for 5 Hp, 1750 rpm input, 125 rpm output Appears to be rebuilt and unused since (1) available
Stock Number: B-3695 5 HP LIGHTNIN RIGHT ANGLE DRIVE 71 C 5 Mfg. Lightnin model 71C5 5 Hp, 1160 rpm, 230/460v, 3 ph 9.17 ratio, 122 rpm shaft speed (1) available
Stock Number: B-3594 5.5 HP FALK INLINE GEAR REDUCER Mfg. Falk sub. of Sunstrand Corp. Model RK2050F3A, m.o. 990U0356 Rated for 5.5 Hp, 1753 rpm in, 13.5 rpm out 127.7 ratio, class 2, service factor 1.0 Output shaft = 2 7/8 x 5 inch, input = 1.5 x 3 inch Motor is optional (1) available
Stock Number: B-3286 7 .5 HP NORD GEAR MOTOR INLINE Mfg. Nord Gear Corp. 2006208910963 7.5 Hp, 1735 rpm, 3ph 5.50 ratio, 318 rpm output (1) available
Stock Number: B-1967 Mfg. Chemineer Model MDV-75-317 7.5 Hp, 1160 rpm, 208-220/440v, 3ph 17.09 ratio. Vari-speed pulleys 2480/308 rpm input, 145/18 rpm output (1) available
Stock Number: B-1417 Mfg. Dodge Size 250CM40F, ID 2815434001X4 Reliance 7.5 Hp, 1750 rpm, 3ph Includes brake motor. Was like new when arrived (1) available
Stock Number: B-3584 (2) 7 .5 HP EURODRIVE RIGHT ANGLE DRIVE 36-19 RPM Mfg. Eurodrive 7.5 Hp, 1740/860 rpm input, 36/19 rpm output 230/460v, 3ph Flange mount, (2) similar with same ratios available! (2) available
Stock Number: B-2648 7.5 HP RIGHT ANGLE DRIVE MIXER CLEVELAND 161 RPM Mfg. Cleveland Model ALS-5 7.5 Hp, 1170 rpm, 230/460 v, 3ph 7.25 ratio, 161 rpm output We may be able to shorten the mounting height (1) available
Stock Number: B-3083 Mfg. Link Belt Model 2947Y130U, size 5DTB-2 38.4 ratio, rated fpr 8.44 Hp, class 2 7/8 x 2 inch input shaft, 2.5 x 5 inch output shaft (1) available
Stock Number: B-3039 10 HP RIGHT ANGLE DRIVE MIXER 94 C 10 Mfg. Lightnin Model 94 C 10 10 Hp, 1730 rpm, 230/460v, 3ph 25.6-1 ratio, 68 rpm output Packing gland seal, flange mount (1) available
Stock Number: B-3477 (3) 10 HP PRO-QUIP RIGHT ANGLE DRIVE 56 RPM 10QHX31B Mfg. ProQuip Model 10QHX31B 10 Hp, 1750 rpm, motor may not be exactly as pictured. 230/460 v or 460 v 31.1 ratio, 56 rpm output UNUSED!!! With or without Stainless steel shafts and turbines (3) available
Stock Number: B-3528 10 HP LIGHTNIN RIGHT ANGLE DRIVE 94 Q 10 Mfg. Lightnin Model 94 Q 10, no. 9155967101 Ratio 20.8, 84 rpm output (1) available
Stock Number: B-3585 (2) 10 HP EURODRIVE RIGHT ANGLE DRIVE 24 RPM OUTPUT Mfg. Eurodrive 10 Hp, 1740 rpm input, 24 rpm output, 73.3 ratio 230/460v, 3ph Flange mount, (2) similar with same ratios available! (2) available
Stock Number: B-3590 (2) 10 HP EURODRIVE RIGHT ANGLE DRIVE 38.7 RATIO 2 SPEED Mfg. Eurodrive 10/5 Hp, 1760/870 rpm input 38.77-1 ratio, 45/22.5 rpm output 230/460v, 3ph Flange mount (2) available
Stock Number: B-2799 15 HP RIGHT ANGLE DRIVE MIXER NETTCO WT 50 Mfg. Nettco (now owned by Lightnin) Believed to be a model WT-50 (plate under) 15 Hp, 1750 rpm, 500v dc, 27a, 300v dc field Believed to be 12.66 ratio (1) available
Stock Number: B-3012 15 HP RIGHT ANGLE DRIVE MIXER 76 Q 15 Mfg. Lightnin Model 76 Q 15 30.7 ratio, 56 rpm with 1750 rpm input (1) available
Stock Number: B-3285 Mfg. SEW Eurodrive 282R801-50, 89005591 15 Hp, 1750 RPM, 230/460V, 3PH 204 rpm output (1) available
Stock Number: B-1874 15 HP LIGHTNIN RIGHT ANGLE DRIVE SX 84 Q 15 Mfg. Lightnin Model SX 84 Q 15 26-1 ratio, 68 rpm output 15 Hp, 1760 rpm, 460v, 3ph (1) available
Stock Number: B-3521 15 HP LIGHTNIN RIGHT ANGLE DRIVE 75 Q 15 Mfg. Lightnin Model 75 Q 15 32.1 ratio, 54.5 rpm output 39 inch o/a height to top of lifting lug (2) available
Stock Number: B-3700 15 HP LIGHTNIN RIGHT ANGLE DRIVE 76 Q 15 Lightnin right angle drive model 76-Q-15 15 Hp, 1170 rpm, 230/460v, 3ph 30.2 ratio, 37 rpm shaft speed (1) available
Stock Number: B-2482 20 HP LIGHTNIN RIGHT ANGLE DRIVE 3 RPM Mfg. Lightnin 3 rpm output 20 Hp, 1765 rpm. 3/4 Hp pump for oil circulation 208-230/460v, 3ph, 60hz Stainless steel stub shaft and face Came in mounted on 750 gallon tank with ribbon agitator. See no. E-2484 (2) available
Stock Number: B-2504 20 HP PHILADELPHIA RIGHT ANGLE DRIVE MIXER Mfg. Philadelphia Model 3809SPTO 47.1-1 ratio, rated for 20/13.3 Hp 37 rpm shaft with 1750 rpm input Buy with or without motor setup (1) available
Stock Number: B-3082 Mfg. Foote Jones Model 822SL, no. 202CF025 25.6 ratio, class 1 “C” face motor mount 2 x 3.75 inch output shaft (1) available
Stock Number: B-3596 (1 right angle, 1 left angle) Mfg. Textron 25-1 ratio 750 w (1.01 Hp)motor, 2000 rpm with encoder, 3 ph 4-wire Model MARU25A679-1 (left angle) 1.25 x 1.75 inch output shaft Stk. no. B-3595 is a -2 (right angle) (2) available
Stock Number: B-2515 (4) 30 HP LIGHTNIN RIGHT ANGLE DRIVE MIXER 77 Q 30 Mfg. Lightnin Model 77Q30 30.7-1 ratio, 37/28 rpm output 30/22 Hp 2-speed motor, 1185/880 rpm, 460v Has 5.5 inch diameter steel stub shaft (4) available
Stock Number: B-2862 40 HP LIGHTNIN RIGHT ANGLE DRIVE MIXER 76 C 40 Mfg. Lightnin Model 76 C 40 20.2 ratio, 84 rpm with 1750 rpm input (1) available
Stock Number: B-3118 50 HP LIGHTNIN DRIVE LAR-130CMX Mfg. Lightnin Model LAR-130CMX, s/n 82-3763402 Rated for 50 HP, 39.1 ratio 15/30 rpm output (1) available
