Stock no. B-4429 15 hp SANITARY STAINLESS STEEL TRI-BLENDER INLINE MIXER Plate missing, but most likely TRI-CLOVER Division Of Alfa Laval Sanitary stainless steel 316 Tri-clamp 3 inch top inlet, 2 inch side outlet Comes with Y connection for input mix 15 hp 1760 rpm, 3 ph, 230/460 volt Currently in our shop being rebuilt. […]
Stock no. B-4428 Stainless Steel Double Ribbon for a 150 cu. ft. Ribbon Blender Believed to be for a Young Ribbon Blender 54 inch od outer ribbon diameter, 36.5 inch od inner ribbon Center shaft is 7 inch diameter x 114.75 inch long with 149 inch overall length Ends are 4.5 inch diameter with one […]
Stock no. B-4417 8 quart STAINLESS STEEL TWIN SHELL DRY BLENDER Paterson Kelley number LB 10944, rated for 300 lbs per cu. ft. Single phase 115-230 volt, 1/4 Hp, 1725 rpm motor gear reduced. Mounted on ss wheeled cart O/a 31 x 22 x 50 inch tall with bottom up 7 3/8 inch id top […]
Stock no. B-4401 50 cu. ft DOUBLE CONE BLENDER CARBON STEEL 66 inch diameter x 16 inch straight side 25 inch bottom cone and 30 inch top cone Approximately 50 cu. ft. volume with 5 Hp motor (plate needs to be cleaned) Belt drive to gear reducer 12 inch bottom outlet with 5 inch valve […]
Stock no. B-4392 16 quart POLYCARBONATE TWIN SHELL DRY BLENDER PK Paterson Kelly number LB 8047 Single phase 115 v fractional Hp motor Chain drive (1) available
Stock no. B-4384 POLISHED STAINLESS STEEL 2 liter V BLENDER for mixing powders Model VH-2, V Series Mixer, s/n JC170036, criterion no. JB20018-2004 Believed to be made by Vevor 2 liter total volume, 1.2 liter working, approximately 1.5 lb mix capacity. 60 watts, 110 volt, 1 Ph, 60 Hz Has speed control marked 0-90 and […]
Stock no. B-4324 2 cu. ft. KELLY DUPLEX PLOW BLENDER CARBON STEEL Made by The Duplex Mill and Manufacturing Co. Model 191, serial no. 62076 1 Hp, 3 phase motor to 43.35 to 1 ratio gear box, 1700 rpm in, 39 rpm out Control box, Start, Stop, and Reset Has (2) plow type rotating blades. […]
Stock no. B-4136 45 cu. ft. SANITARY STAINLESS STEEL DOUBLE CONE BLENDER Paul O Abbe, compares to model RCB-29 45 cu. ft. full capacity, 29 cu. ft. working capacity 54 inch inside diameter x 16 inch with 24 inch cones 14 inch inside diameter top inlet with lid 8 inch bottom outlet with valve 5 […]
Stock no. D-1098 (2) 133 cu. ft. J H DAY 304 STAINLESS STEEL ROTARY VACUUM DRYER SYSTEM 44 inch diameter x 16 ft long shell rated for Full Vacuum, jacket rated for 40 psi @ 275 deg. F National Board stamped. Typical print on file and U-1 report 25 Hp, 460 v, 3 ph Includes […]
Stock no. D-1094 70 cu. ft. PFAUDLER GLASS LINED DOUBLE CONE DRYER Serial no. R581-3117, year 1982, NB no. 41830 Rated for Full Vacuum/30 psi @ 650 deg. F Jacket rated for 50 psi @ 350, 45 psi with vacuum 70 cu. ft. working capacity, 5015 glass. Approx. 180″ wide x 5′ x 130″ tall o/a […]
Stock no. B-3808 2 hp SANITARY STAINLESS STEEL TRI-BLENDER INLINE MIXER Model no. 2116MD B40, s/n 03014 Manufacturer TRI-CLOVER Division Of Alfa Laval Sanitary stainless steel 316 Tri-clamp 2 inch for powders, 1.5 inch for liquid in and out Top feed cone included (cone may not be exactly as pictured) Motor 2.5 hp 3600 rpm […]
Stock no. D-0013 3 CU. FT. TWIN SHELL JACKETED BLENDER DRYER STAINLESS STEEL Manufacturer PATTERSON-KELLEY CO. Model SOLIDS PROCESSOR, #155883 O/A Dimensions 6′ 10” x 5′ 3” Stainless steel contacts Jacket rated for 30 PSI @ 250 F. Shell rated for Full Vacuum @ 250 F ( 2) 16 1/4” TOP INLETS, 6” bottom center […]
Stock Number: B-1001 1.5 HP ZIG-ZAG CONTINUOUS BLENDER 6000 lbs. per hour Mfg. PATTERSON-KELLEY CO. Size 14CLSS, no. 183187, stainless steel 1.5 Hp drive motor, 2 Hp intensifier bar, 230/460 v, 3ph Rated for 55 lbs. per cu. ft.density, to 6000 lbs per hr Continuous blender with liquid feed It is 102 inch overall in […]
Stock No. B-2877 5 cu. ft. MUNSON PADDLE BLENDER HD 1.5-3 MS Mfg. MUNSON, model HD1.5-3MS 5 cu. ft. working, 7 cu. ft. total, 400 Lbs capacity Carbon steel, 20 inch x 36 inch x 20 inch deep internal measurements 5 ft. long overall. Removable top with access door. On wheels 12 inch x 7 inch plug […]
Stock Number: B-3389 5 CU. FT. STAINLESS STEEL TURBULENT MIXER BLENDER Twin Shaft Turbulent Mixer Blender 13 x 48 x 15 inch internal dimensions No manufacturer id plate (2) 2 inch side outlets Motor with drive setup to be included (1) available
Stock Number: D-1080 20 CU. FT. STAINLESS STEEL DOUBLE CONE VACUUM DRYER-BLENDER Mfg. KOMLINE SANDERSON No. B-26. s/n 1-221, 1966, National Board no. 60 304 STAINLESS STEEL w/ carbon steel jacket Full vacuum and 20 psi @ 300 F. shell, Jacket = 50 psi 5 hp, 1745 rpm, 208-220/440 v, 3ph, 60hz U-1 report on […]
Stock Number: D-1063 20 CU. FT. PATTERSON KELLEY TWIN SHELL DRYER BLENDER Mfg. Patterson Kelley STAINLESS STEEL CONTACTS!, carbon steel jacket Jacket rated for 15 psi. Has internal vacuum bar. Priced with motor and stand setup (1) available
Stock Number: D-1083 21 CU. FT. STAINLESS STEEL DOUBLE CONE VACUUM DRYER-BLENDER Mfg. PAUL O. ABBE, INC. Serial no. A40755, RotoCone, maximum bulk density of 150 lbs./cu. ft. 32 cu. ft. total. Working volume 65% fill level is 21 cu. ft. 1.5 Hp gear motor for drive, 5 rpm drum speed, 5 Hp 1165 rpm for […]
Stock Number: B-2381 40 CU. FT. STAINLESS STEEL TWIN SHELL BLENDER Mfg. Patterson Kelley Co. Liquids Solids Blender s/n 107324 Rated for 65 lbs/cu. ft. 5 Hp 1740 rpm drive motor, 15 Hp, 3500 rpm bar motor Priced setup on stand with motor and guards Will be sandblasted. has a lot of small dents (1) […]
Stock Number: B-0996 60 CU. FT. DOUBLE CONE BLENDER with LIQUIDS-SOLIDS BAR Carbon steel construction 80 inch diameter x 6 ft.. 18 inch top manway, 10 inch outlet 5 and 3/4 Hp drive motors, 25 Hp bar 230/460 v, 3ph, 60hz Liquids-solids bar and vacuum (1) available
Stock Number: D-1048 Mfg. Pfaudler Model 72-45-CD-SB 107 cu. ft. total volume, 70 cu. ft. working Does have patches in glass Jacketed (1) available
Stock Number: B-1076 120 CU. FT. CARBON STEEL RIBBON BLENDER 4.5 ft. x 8 ft. x 61 inch deep Carbon steel double ribbon 25 Hp, 230/460 volt, 3ph, 60hz 8 inch bottom end outlet De-lumpers pictured on top are not included (1) available
Stock Number: D-1040 100 CU. FT. DOUBLE CONE VACUUM DRYER-BLENDER FV JACKETED Mfg. PATTERSON INDUSTRIES Serial no. Y1495, National Board no. 693 Full vacuum/15 psi internal 15 psi JACKET @ 250 deg. F Carbon steel 6 ft. 6 in. diameter w/(2)3 ft. cones (1) available
Stock Number: B-0612 150 CU. FT. TWIN SHELL V BLENDER PATERSON KELLEY Mfg. PATTERSON-KELLEY CO. Carbon steel, rated for 50 LBS/CU. FT 5 ft. x 3 ft. x 8 ft. 12 in. outlet,(2)18 in. inlets DRY BLENDER 10 HP/1745 RPM (1) available
Stock Number: D-1084 265 LBS. PER HR. NIRO STAINLESS STEEL SPRAY DRYER Mfg. NIRO INC. Serial no. 6938-A1, type WT 28-125 90 in. diameter. Stainless steel Atomizer type FU 11B AA02, s/n 919, Niro 265 lbs. evaporating rate, 800 acfm Last used for turning liquid flavorings to powder at the above rate AS IS some […]
Stock Number: B-1518 (2) 300 CU. FT. DOUBLE CONE BLENDER GEMCO CARBON STEEL mfg. GEMCO/ General Machine Co. 10 ft. 6 in. x 30 in. w/50 in. and 54 in. cones 14 in. and 18 in. outlet and inlet 25 hp/1765 rpm Carbon steel Includes stand and drive (1) body with drive and stand and […]
Stock Number: D-1058 333 lbs. per hour ANHYDRO STAINLESS STEEL SPRAY DRYER Mfg. Anhydro Inc. Series 6 Model 3, no. 78-952-OA 304 stainless steel, originally gas fired with electric duct heaters 122 inch diameter x 166 inch and 7 ft, cone 480 v, 3ph, 5 KW. 333 lbs/hr powder production 450 lbs/hr feed, 117 lbs/hr […]
Stock Number: D-1057 427 lbs. per hour ANHYDRO STAINLESS STEEL SPRAY DRYER Mfg. ANHYDRO, INC. Series 6 Model 4, O/N 82-1584, 1983 10 ft. 3 in. x 18 ft. w/7 ft. cone, plus Dust Collector 316 stainless steel feed, balance 304 stainless steel 577 lbs/hr water feed. 150 lbs/hr evaporation 427 lbs.hr powder Originally with […]
Stock Number: B-0608 100 GALLON WERNER PFLEIDERER STAINLESS STEEL DOUBLE ARM MIXER Mfg. Werner Pfleiderer Type UK14V1H, machine no. 138304 Bramley Bekin type blades, stainless steel contacts Carbon steel jacket Hydraulic tilt dump 150/75 Hp 2 speed motor SELLING AS IS (1) available
Stock Number: B-0279 150 GALLON JACKETED SIGMA BLADE MIXER BAKER PERKINS VACUUM Mfg. Baker Perkins Model 16RIM2, no. 41767, NB 1981 Carbon steel. Jacket rated for 125 psi @ 450 F Internal rated for vacuum. Can take up to 150 HP 45 in. x 33 in. x 4 ft. deep bowl (2) 4.5 in. bottom […]
