5 Hp Lightnin Flange Mount Right Angle Drive 21.2:1 ratio

Stock no. B-4467 (2) 5 Hp Lightnin Flange Mount Right Angle Drive 21.2:1 ratio, 83/28 rpm Model 72C5VM, serial no. 7710624 (2nd is 7710623) 5 Hp, 1730 rpm, 208-230/460v, 13.2/6.8a, 3ph, 60hz (2nd is 230/460v) Has 13 inch od 8-bolt flange with packed seal Takes a 2.5 inch diameter shaft, not included. Measures 17 x […]

175 gallon Stainless Steel Slant Bottom Portable Tank

Stock no. A-5669 (2) 175 gallon Stainless Steel Slant Bottom Portable Tank, Open top 38 inch id x 36.25 > 36.75 inch deep with open top 1 inch bottom > side outlet with valve Mounted on fork slots for ease of moving Would make a good disperser tank Very clean and ready to ship (2) […]

100 gallon Stainless Steel Dual Motion Sweep Tilt Kettle 90 psi

Stock no. E-4670 100 gallon Stainless Steel Dual Motion Sweep Tilt Kettle Hamilton serial no. 1479 with jacket rated for 90 psi @ 650 deg. F 38 inch id x 28 inch deep with 1.5 inch bottom center outlet Has sweep agitator with counter rotating blades Agitator tilts up and kettle tilts to dump if […]

Gaulin 2 stage Homogenizer with 5000 psi gauge

Stock no. B-4469 Gaulin 2 stage Homogenizer with 5000 psi gauge Has 1.5 inch inlet and outlet O/a 40 x 52 x 47 inch tall Possibly a Gaulin model 500 CGD from the late 1940s. The ratings would be roughly 500 GPH at 3000 PSI No markings (1) available SALE PENDING

275 liter Stainless Steel Portable Jacketed Tank

Stock no. E-4674 (4) 275 liter Stainless Steel Portable Jacketed Tank No plate with a pressure rating. MFG All-Weld of Ontario, Canada 30 inch diameter x 24 inch with flat bottom and clamped top Has side jacket with (4) side inlet and outlet, 1 inch threaded > tri-clamp on 2 24 inch center clamped lid […]

1000 gallon Stainless Steel Dimple Jacketed Tank with Mixer

Stock no. E-4678 1000 gallon Stainless Steel Dimple Jacketed Tank with Mixer Perry Products s/n A8667, year 1970, National Board no. 394 3/16 inch shell and bottom hd. 0.109 inch jacket 2-zone bottom and side jacket rated for 75 psi @ 320 deg. F (2)2 inch + (2)1.5 inch  bottom jkt. fittings. 1 inch +(3) […]

300 liter 316L Stainless Steel Portable Jacketed Tank FV 15 psi

Stock no. E-4673 300 liter 316L Stainless Steel Portable Jacketed Tank FV 15 psi Mfg. by INOX, Ontario, Canada. P/n D.P.-10, 5/96, 300 L capacity Material 2205/316L. Rated for FV and 15 psi @ 300 deg. F Has side jacket with side inlet and outlet, 1 inch tri-clamp 24 inch center clamped lid with (7) […]

3 inch Ampco Stainless Steel Displacement Pump AL33

Stock no. P-3432 (6) 3 inch Ampco Stainless Steel Displacement Pump Model AL 33-M (one is AALB33-102-12SM) 7.5 Hp, 1770 rpm, 230/460v, 3ph (one has a 3500 rpm motor) 4.22:1 ratio gear reducer 3 inch Tri-clamp fittings Mounted on stainless steel cart, motors have stainless steel casings From a food plant (6) available, PRICED FOR […]

500 gallon STAINLESS STEEL JACKETED KETTLE

Stock no. E-4672 500 gallon STAINLESS STEEL JACKETED KETTLE Alfa Laval Vicarb serial no. 14072.13, year 1955, made in Canada CRN 93884.5. Jacket rated for 100 psi @ 300 deg. F > 20 deg. F Second plate indicates 80 psi steam max. Has 3/4 side and bottom jackets, 2 zone 59 inch inside diameter x […]

6 Bag Sanitary Stainless Steel Multi Basket Bag Filter

Stock no C-2796 6 Bag Sanitary Stainless Steel Multi Basket Bag Filter Baskets are 7 inch diameter x 26 inch deep Vessel is 24 inch diameter x 26 inch with a dished bottom and dished top (4) legs with a 21.25 inch square foot print. Bottom and side fittings are 3 inch tri-clamp. There is […]

210 sq. f. 316 Stainless Steel Shell and Tube Heat Exchanger

Stock no. G-4047 210 sq. f. 316 Stainless Steel Shell and Tube Heat Exchanger MECO, Mechanical Equipment Co inc serial no. S81737-1, year 2007 National Board no. 441. Shell and Tubes rated for 125 psi @ 350 deg. F to -20 F Has (281) 1/2 inch od tubes x 66 inch long. Approximately 210 sq. […]

Waukesha model 320 U2 SS Displacement Pump

Stock no. P-3425 Waukesha model 320 U2 SS Displacement Pump Serial no. 2515447 Motor is approximately 25 Hp, plate is missing Mounted on a stainless steel platform Just in, more info to follow. (1) available

250 gallon GROEN STAINLESS STEEL JACKETED KETTLE

Stock no. E-4663 250 gallon GROEN STAINLESS STEEL JACKETED KETTLE Sweep Option Model II 250, No. 68989.  Jacket rated for 40 psi, year 1962 52 inch diameter x 39 inch deep. 6 ft. o/a height on (4) legs Approximately 2 to 2.5 inch bottom outlet with pop-up valve > 1.5 inch outlet. Has hinged lid […]

500 gallon UNUSED SS JACKETED KETTLE with HORIZONTAL SWEEP

Stock no. E-4656 (4) 500 gallon UNUSED SS JACKETED KETTLE with HORIZONTAL SWEEP D C Norris + Co. Ltd, serial no. N3982, year 2020 National Board no. 57. Jacket rated for 100 psi @ 338 deg. F > -20 deg. F Bought for a project that was cancelled. Unused! Just in, more details to follow. […]

2 x 3-10 Goulds 316 SS Centrifugal Pump Model 3196 100 gpm

Stock no. P-3422 (4) 2 x 3-10 Goulds 316 SS Centrifugal Pump Model 3196 Serial no. 713G554-4 with a 10 inch impeller 3 inch inlet x 2 inch outlet 10 Hp, 1725 rpm, 230/460 volt, 26.8/13.4 amp, XP motor Rated for 100 gpm and 107 ft. hd. (3) more similar without motors  

100 gallon SS Jacketed Kettle Single Motion Sweep Kettle Clamped Top

Stock no. E-4655 100 gallon SS Jacketed Kettle Single Motion Sweep Kettle Clamped Top Hamilton Kettles  serial no. B-3637-1, year 1975 National Board no. 3516, jacket rated for 80 psi, internal 15 psi @ 312 deg. F 36 inch id x 30 inch deep. 2 inch threaded bottom center outlet>tri-clamp valve Top threaded inlets = […]

2 inch WILDEN 316 STAINLESS STEEL DIAPHRAGM PUMP M8

Stock no. P-3415 2 inch WILDEN 316 STAINLESS STEEL DIAPHRAGM PUMP M8 Model M8-SO, NE/NE/NE, serial no. 47448 2 inch threaded inlet and outlet with quick connect coupler Air powered On stainless steel cart, o/a 19 x 38 x 37 inch tall Tested and ready to ship. (1) available  

165 gallon STAINLESS STEEL CONICAL TOTE TANK IBC Mueller

Stock no. A-5658 (3) 165 gallon STAINLESS STEEL CONICAL TOTE TANK IBC Mueller Porta-Tank 44 inch x 44 inch x 15 inch straight side, 18 inch cone bottom, flat top Has 2 inch bottom center outlet and 18 inch top manway. Top support for a clamp on mixer (optional) Has a dimple side jacket rated […]

1500 gallon Sanitary Stainless Steel Insulated Tank with Sweep

Stock no. E-4653 1500 gallon Sanitary Stainless Steel Insulated Tank with Sweep Agitator Crepaco serial no. A-1890. Selling as a single wall tank !! Has a dimple jacket that leaks with (3) side fittings and (2)bottom fittings 84 inch inside diameter x 66 inch straight side and dished top, concave bottom 2 inch bottom to […]

4 inch Model 220 Waukesha Sanitary SS Displacement Pump

Stock no. P-3409 (2) 4 inch Model 220 Waukesha Sanitary SS Displacement Pump Model 220, serial no. 282623-01 (second is 422173-06  ) Both with 10 Hp, 1760 rpm, 230/460 volt motors and belt drives 4 inch threaded fittings. Mounted on stainless steel platform All just in from a food plant (2) available

Waukesha Model 224 U1 Sanitary SS Displacement Pump 11 x 4-4 inch

Stock no. P-3413 (3) Waukesha Model 224 U1 Sanitary SS Displacement Pump (3) units available. This one built in 2016, others in 2015 and 2009 All with 10 Hp, 1760 rpm, 230/460 volt motors and gear reducers 11 x 4 inch top inlet with 4 inch bottom outlet This one has an 8 inch diameter […]

200 liter/53 gal STAINLESS STEEL DIMPLE JACKETED TANK SFI

Stock no. E-4652 200 liter/53 gal STAINLESS STEEL DIMPLE JACKETED TANK Stainless Fabrication Inc. serial no. 18107-1-1, model VE069300 Could not see a mfg’s plate, info provided by previous owner 29.5 inch inside  x 19.5 inch deep with flat bottom and open top (57 gal total) On 4 legs with wheels, external handles, o/a 40 […]

100 gallon STAINLESS STEEL DIMPLE JACKETED TANK 50 PSI

Stock no. E-4650 100 gallon STAINLESS STEEL DIMPLE JACKETED TANK 50 PSI Perma San model 100 gallon JOVS, serial no. 33812-2 Single zone side and bottom dimple jacket rated for 50 psi @ 300 deg. F 30 inch id x 33 > 34.5 inch slant bottom and open top (4) legs, 62.5 inch to top […]

6 sq. ft. Plate Heat Exchanger 2 inch tri-clamp fittings WCR 150 psi

Stock no. G-4046 6.329 sq. ft. Plate Heat Exchanger 2 inch tri-clamp fittings WCR Inc. model WCR-A216M, serial no. 2990, year 2015 Rated for 150 psi @ 266 deg. F.  6.329 sq. ft. Has (4) 2 inch tri-clamp fittings Plate pak is 0.69 inch thick. O/a 13 inch x 9.5 inch with fittings x 37.5 […]

2.5 inch Sanitary Stainless Steel Displacement Pump 20 Hp

Stock no. P-3404 2.5 inch Sanitary Stainless Steel Displacement Pump Matches up with Wright Flow Technologies model 600 S/n CC-927210-1-1-R1-2 with 2.5 inch tri-clamp fittings 20 Hp, 1770 rpm, 230/460 v, 49.2/26.1 a, 3 ph, 60 hz Gear reducer ratio is 2.76:1, 641 output speed Nominal rating 90 gpm at this speed Mounted on a […]

1/4 Hp Right Angle Mixer 10:1 ratio Variable Speed

Stock no. B-4463 1/4 Hp Right Angle Mixer 10:1 ratio Variable Speed Mfg. by Brother of Japan for Hyclone. Originally with 50 liter single use reactor, no. CC0605-3, p/n SV50171-01, 9/06 Only parts of the reactor are still with it. Mounted on Stainless steel Cart O/a 24 x 36 x 51 inch to top of […]

Blue M model OV-472A-3 CONVECTION OVEN 38 TO 260 deg C

Stock no. G-4042 Blue M model OV-472A-3 CONVECTION OVEN Serial no. OV3-30104 Rated for 38 to 260 deg C 12.75 x 12 x 12 inch inside, 20 x 21.5 x 28.75 inch o/a dimensions 120v, 1 ph, 60 hz, 11 amp, 3 amp for motor only Has 2 side vents and a rear probe Just […]

Fisher Scientific Isotemp Oven Model 750F 50 to 275 deg. C

Stock no. G-4043 (3) Fisher Scientific Isotemp Oven Model 750F Temperature Range: 50-275C Recovery Time @ 200C: 2.5minutes Rise Time to 275C: 80 minutes Air Exchanges per hour: 22 BTU/hr Output: 1325 at 100C and 3095 at 200C Electrical: 120V, 60Hz, 15.5A Power: 1860W Chamber Volume: 5.0 cu. ft. Chamber dimensions: 18 x 18 x […]

3 Hp Fitzmill Homoloid Grinder Rotating Blades Model J

Stock no. C-2795 3 Hp Fitzmill Homoloid Grinder Rotating Blades Model J, serial no. 1537 3 Hp, 3475 rpm, 230/460 v, 7.8/3.9 a, 3 ph, XP Has (3) sets of 4 blades that rotate One screen with 1/8 inch perforations Top pan feed. On stand with wheels 30 x 30 x 42 inch tall. Control […]

40 gallon STAINLESS STEEL STEAM JACKETED KETTLE LEGION

Stock no. E-4648 40 gallon STAINLESS STEEL STEAM JACKETED KETTLE Legion serial no. 70633, National Board no. 51, year 1957 Jacket rated for 40 psi @ 300 deg. F 29.5 inch inside diameter x 21.5 inch deep. (3) legs, 40.5 inch > top lip Has a 1.25 inch bottom center outlet and bottom outlet Also […]

25 gallon STAINLESS STEEL STEAM JACKETED KETTLE GROEN

Stock no. E-4649 25 gallon STAINLESS STEEL STEAM JACKETED KETTLE GROEN model G25, serial no. and NB no. 11135 1959GM-717, 58109 U and W stamped Jacket rated for 25 psi @ 300 deg. F 28 inch inside diameter x 16 inch deep. (3) legs, 28 inch > top lip Has a 1 inch bottom center […]

150 gallon Stainless Steel Steam Jacketed Kettle Hamilton 100 psi

Stock no. E-4647 150 gallon Stainless Steel Steam Jacketed Kettle Hamilton Brighton Style SA, Hamilton serial no C3313-2, year 1981. National Board no. 4862 . Jacket rated for 100 psi @ 328 deg. F Brighton plate dated 8/20/84, no. 144 C-6612. U and W stamped 44 inch inside diameter x 34 inch deep on 3 […]

150 gallon Stainless Steel Steam Jacketed Kettle Groen

Stock no. E-4646 150 gallon Stainless Steel Steam Jacketed Kettle Groen Model N150SP, serial no 27742G, year 1951. Jacket rated for 40 psi 42 inch inside diameter x 34 inch deep on 3 legs. 46 inch to top lip. Originally with 2.5 inch threaded bottom center outlet but welded shut Has bottom and side jacket […]

50 gallon SS Jacketed Kettle Single Motion Sweep Kettle

Stock no. E-4645 50 gallon SS Jacketed Kettle Single Motion Sweep Kettle Hamilton Kettles Brighton Division serial no. D-809-1, style SA National Board no. 5058, year 1988. Jacket rated for 90 psi @ 200 deg. F. Has side and bottom fittings & relief valve 1.5 Hp, 1762 rpm (gear reduced 300-1900 rpm), 230/460 v, 4.6/2.3 […]

50 gallon SS Jacketed Kettle Single Motion Sweep Kettle

Stock no. E-4644 50 gallon SS Jacketed Kettle Single Motion Sweep Kettle Hamilton Kettles Brighton Division serial no. C-9248-2, style SA National Board no. 5855, year 1987. Jacket rated for 90 psi @ 200 deg. F. Has side and bottom fittings & relief valve 1.5 Hp, 1740 rpm (gear reduced), 230/460 v, 5.2/2.6 amp drive, […]

80 gallon 316 STAINLESS STEEL STEAM JACKETED TILT KETTLE

Stock no. E-4641 80 gallon 316 STAINLESS STEEL STEAM JACKETED TILT KETTLE Similar to our stk. no. E-4640 Cleveland kettle but missing the plate Matches up with model KDL-80-T. Has a 1.5 inch bottom to side outlet with a valve Bottom jacket drain, side jacket inlet and outlets. 33 inch inside diameter x 28 inch […]

3 HP SILVERSON HOMOGENIZER MIXER DX60 ROTOR STATOR TYPE

Stock no. B-4452 3 HP SILVERSON HOMOGENIZER MIXER  ROTOR STATOR TYPE Model DX60, sn 4B2114 3 Hp, 3500 rpm, 208-230/460v, 3ph, 60hz with speed control Currently mounted on a 60 gallon tank, stock no. A-5644 (1) available with or without tank

60 gallon STAINLESS STEEL CONE BOTTOM TANK WITH SILVERSON MIXER

Stock no. A-5644 60 gallon STAINLESS STEEL CONE BOTTOM TANK WITH SILVERSON MIXER 23 inch inside diameter x 34 inch straight side with cone bottom and open top 3 Hp Silverson Homogenizer Rotor-Stator mixer, 4B2114, model DX60(stk. B-4452) 208-230/460v, 3ph, 60hz with speed control 2.5 inch bottom center outlet. (1) available with or without mixer

3/4 Hp Brawn Vertical Mount Gear Reduced Mixer

Stock no. B-4453 (3) 3/4 Hp Brawn Vertical Mount Gear Reduced Mixer with SS Shaft and Blades Brawn Model BGMF 75 . 3/4 Hp, 208-230/460v, 3ph, 60hz Includes stainless steel shaft and a blade Came in with our stock no. A-5633, 1200 gallon tank (3) available

3/4 Hp Angled Mount Gear Reduced Mixer Brawn BGM 75

Stock no. B-4459 (5) 3/4 Hp Angled Mount Gear Reduced Mixer with SS Shaft and Blades (4) are Brawn Model BGM 75 and (1) has a 1 Hp motor (1) is a similar Nettco 3/4 Hp gear reduced mixer all are 208-230/460v, 3ph, 60hz Includes stainless steel shaft and a blade Came in with our […]

235 gallon STAINLESS STEEL CONE BOTTOM TANK WITH MIXER

Stock no. A-5645 (6) 235 gallon STAINLESS STEEL CONE BOTTOM TANK WITH MIXER 38 inch diameter x 47 inch straight side with cone bottom and open top Optional top mounted 3/4 Hp gear reduced Brawn mixer (4) sidewall internal baffles 2 inch bottom center outlet, (2) 2 inch side outlets and (2)side inlets (4) legs. […]

200 gallon LEE METAL SS JACKETED KETTLE ANGLED SWEEP

Stock no. E-4662 200 gallon LEE METAL SS JACKETED KETTLE ANGLED SWEEP AGITATOR Model 200 D7SI, year 2010, sn 61509-1-1, NB 11821 Jacket rated for 90 psi @ 332 F > -20 F dimensions to be added Takes a 3 inch flush mount valve, but not with it Has 4.5 inch side outlet and jacket […]

ROSS 10 HP XP INLINE MIXER with 2 inch fittings HMS-410

Stock no. B-4451 ROSS 10 HP XP INLINE MIXER with 2 inch fittings Model no. HMS-410 with 4 inch rotor 316 Stainless Steel with rotor-stator configuration 10 Hp, 3520 rpm, 230/460 volt, 23.0/11.6 amp, XP 2 inch flanged outlet, flat 4-bolt front inlet 240 gpm maximum flow with water (1) available, SALE PENDING

800 mm Filter Press with Recessed Poly Plates 15 sq. meter

Stock no. C-2791 800 mm Filter Press with Recessed Poly Plates Hangzhou Leo Filter Press Co. LTD, China Model XM15/800-UB, no. EOZ131104. Plate no. 6+7+1+1 15 square meter capacity. Full stack of plates in good condition Has hydraulic pump with control cabinet (1) available

1200 gallon STAINLESS STEEL CONE BOTTOM TANK WITH MIXER

Stock no. A-5633 (3) 1200 gallon STAINLESS STEEL CONE BOTTOM TANK WITH MIXER 6 ft. diameter x 70 inch straight side with 9 inch cone bottom and flat top Optional top mounted 3/4 Hp gear reduced Brawn mixer (4) sidewall and (4) bottom internal baffles for excellent mixing 2 inch bottom center outlet, (3) 2 […]

10 liter JAYGO STAINLESS STEEL HIGH INTENSITY MIXER GRANULATOR

Stock no. B-4447 10 liter JAYGO BAKER PERKINS SS HIGH INTENSITY MIXER GRANULATOR. Used Baker Perkins Type 10 Liter High Shear Mixer/ Granulator (similar to Novamix). Serial no. 64642 Sanitary stainless steel construction, 7 inch dia x 11 inch deep jacketed mixing chamber, bottom driven mixer blade, side driven chopper blade, complete with Hinged lid, […]

150 gallon SANITARY STAINLESS STEEL BREWERY TANK CONE BOTTOM

Stock no. A-5632 150 gallon SANITARY STAINLESS STEEL BREWERY TANK 32 inch diameter x 36 inch straight side, approximately 150 gallon total Has 6 inch coned top with 24 inch top center opening, flat lid 7 inch coned bottom with 1.5 inch tri-clamp center outlet 1 inch side inlet, (2) side outlets, and a 1/2 […]

150 gallon SANITARY STAINLESS STEEL BREWERY TANK CONE BOTTOM

Stock no. A-5631 150 gallon SANITARY STAINLESS STEEL BREWERY TANK 32 inch diameter x 36 inch straight side, approximately 150 gallon total Has 6 inch coned top with 24 inch top center opening, flat lid 7 inch coned bottom with 1.5 inch tri-clamp center outlet 1 inch side inlet, (2) side outlets, and a 1/2 […]

100 liter/26 gal SANITARY STAINLESS STEEL TANK

Stock no. A-5628 (3) 100 liter/26 gal SANITARY STAINLESS STEEL TANK Manufactured in 2014 by Blue Current Brewery of China Type SM100, 100 liter capacity. 20 inch inside diameter x 23.75 inch straight side with slant bottom, open top 2 inch bottom elbowed to side outlet with female threaded coupling connection On 3 wheels. Side […]

2080 liter/549 gal SANITARY STAINLESS STEEL JACKETED TANK

Stock no. E-4631 2080 liter/549 gal SANITARY STAINLESS STEEL JACKETED TANK Manufactured in 2014 by Blue Current Brewery of China Type SF2000, 2080 liter capacity. No pressure plate, assume low pressure jacket. Half-side dimple jacket with 3/4 inch fittings 43 inch inside diameter x 74 inch straight side with concave bottom, open top On 4 […]

4 Kw 5 Hp CUMBERLAND GRANULATOR GRINDER MODEL 2030

Stock no. C-2790 4 Kw 5 Hp CUMBERLAND GRINDER MODEL 2030 Serial no. 2030.96027, year 1996 4 Kw/5 Hp , 415/440 volts, 50/60 Hz, 3 phase 330 rpm max rotor speed. 9 x 12 inch opening It has been tested. Additional information to follow

2 Hp, 2 STAGE SPEEDAIRE AIR COMPRESSOR 50 GALLON

Stock no. G-4041 SpeedAire model 3Z220A, 2 stage, 2 Hp, 208-220/440 v, 3 phase, 6.6-6.2/3.1 amp. Tank measures 24 inch diameter x 24 inch, approximately 50 gallons. Will test prior to sale. Has been sitting in our warehouse. Was originally bought for a back up compressor. We are moving and no longer have a need […]

55 gallon STAINLESS STEEL JACKETED REACTOR FV 30 PSI

Stock no. E-4628 (3) 55 gallon STAINLESS STEEL JACKETED REACTOR FV 30 PSI Inox of Canada serial no. 99033-1, O.I.N. 5.1088798, C R N L2188-5, year 2000 (one is 1997 and rated down to 32 F) Shell and side jacket rated for FV/30 psi @ 300 deg. F to -20 deg. F 23.75 inch id […]

22 gallon STAINLESS STEEL JACKETED REACTOR FV 30 PSI

Stock no. E-4626 22 gallon STAINLESS STEEL JACKETED REACTOR FV 30 PSI Inox of Canada serial no. 98023-1, O.I.N. 5.1088774, C R N L4566-5, year 1999 Shell and side jacket rated for FV/30 psi @ 300 deg. F to 32 deg. F 17.75 inch id x 21 inch straight side with dished bottom and hinged […]

220 gallon 304 SS DIMPLE JACKETED SANITARY TANK

Stock no. E-4625 220 gallon 304 SS DIMPLE JACKETED SANITARY TANK Certified by A & B Process Systems, serial no. 30968301, year 2003 National board no. 315, U and W stamped. Single zone jacket Side and bottom dimple jacket rated for 180 psi @ 300 deg. F to -20 deg. F 36 inch diameter x […]

500 gallon 304 STAINLESS STEEL TANK

Stock no. A-5625 500 gallon 304 STAINLESS STEEL TANK with dished bottom, flat top Perry Products model 500 gal SCX, serial no. A-9744 60 inch diameter x 48 inch straight side with slight dished bottom Has a flat top with a hinged lid 3 inch bottom center outlet with a flush mount valve, 18 inch […]

1/2 Hp LIGHTNIN GEAR REDUCED CLAMP MOUNT MIXER 3 PH

Stock no. B-4446 1/2 Hp LIGHTNIN GEAR REDUCED CLAMP MOUNT MIXER Model Nd-2, serial no. 623489 1/2 Hp, 1725/1425 rpm, 60/50 hz, 208-220/440v, 3ph Includes 3/4 x 56 inch stainless steel shaft and 12 inch prop (1) available SALE PENDING

10 gallon STAINLESS STEEL JACKETED TANK W/HEATER

Stock no. E-4624 10 gallon STAINLESS STEEL JACKETED TANK W/HEATER Van Alst Metal Works, NY job no. 3067 13 5/8 inch id x 15>16.5 inch deep, open top and slant bottom 1/2 inch bottom outlet with plunger type valve that operates from above It has a hot water jacket with a 115 volt immersion type […]

5 cu. ft. MUNSON PADDLE BLENDER HD 1.5-3 MS

Stock No. B-2877 5 cu. ft. MUNSON PADDLE BLENDER HD 1.5-3 MS Mfg. MUNSON, model HD1.5-3MS 5 cu. ft. working, 7 cu. ft. total, 400 Lbs capacity Carbon steel, 20 inch x 36 inch x 20 inch deep internal measurements 5 ft. long overall. Removable top with access door. On wheels 12 inch x 7 inch plug […]

15 gpm US Filter Deionization Module CDI-LX

Stock no. C-2612 15 gpm US Filter Deionization Module CDI-LX US Filter Deionization Hot Water Sanitizable Module Model no.CDI-LX compares to IonPure model  IP-LXM30HI-3 Rated for 600 v DC, 10 amps. 15 gpm nominal capacity, 7.5 to 22.5 gpm, 95% recovery Max. feed temperature is 140 deg F., 100 psi max. feed. Silica removal is […]

75 gallon LEE SS DUAL MOTION JACKETED KETTLE SWEEP AGITATOR

Stock no. E-4620 75 gallon LEE SS DUAL MOTION JACKETED KETTLE SWEEP AGITATOR Lee Metal Products No. 958B. Jacket rated for 455 psi @ 293 deg. F 32 inch diameter x 28 inch deep. 2 pc. lid, tilt out sweep agitator Has a sweep with wipers and counter rotating blades Motor specs to follow 3 […]

100 gallon STAINLESS STEEL JACKETED KETTLE

Stock no. E-4622 100 gallon STAINLESS STEEL JACKETED KETTLE 40 inch diameter x 24 inch deep Has a hinged lid with a Legion tag on it. No other plate on the kettle Has a 1.5 inch bottom center to side outlet with a valve that is 13 inches off the ground (2) jacketed fittings. (3) […]

24 KW STERLING HOT WATER HEATER 480 V G2012-F

Stock no. G-4040 24 KW STERLING HOT WATER HEATER 480 V Model G2012-F, serial no. 39K0374 24 Kw heater, 150 psi max pressure 2 Hp pump. Rear fittings for cooling water in and out and for process in and out 480 v, 3 ph, 31.8 FLA.  Motor = 2.9 FLA.  115 v controls (1) available […]

1.5 inch WILDEN SANITARY STAINLESS STEEL DIAPHRAGM PUMP

Stock no. P-3398 1.5 inch WILDEN SANITARY STAINLESS STEEL DIAPHRAGM PUMP 316 stainless steel. Model 4 1.5 inch tri-clamp fittings, inlet and outlet Air powered. Mounted on a stainless steel platform with a 2 gallon air tank for mobile use (1) available

55 gallon HIGH POLISHED SS JACKETED REACTOR 50 and 80 PSI

Stock no. E-4611 55 gallon HIGH POLISHED SS JACKETED REACTOR 50 and 80 PSI Inox serial no. P13-003, yr 2013. CRN M9816.5 Made in Canada Shell rated for 50 psi @ 298.4 deg. F. -20 deg. F @ 50 psi. 15 psi external Side dimple jacket rated for 80 psi @ 298.4 deg. F t0 […]

65 gallon HIGH POLISHED SS JACKETED REACTOR 45 and 90 PSI

Stock no. E-4612 65 gallon HIGH POLISHED SS JACKETED REACTOR 45 and 90 PSI Inox serial no. P15-030, yr 2016. CRN R2112.5 ASME stamped, W/RT-4, U stamped. Made in Canada Shell rated for 45 psi @ 300 deg. F to -20 deg. F Side dimple jacket rated for 90 psi @ 300 deg. F t0 […]

100 gallon HIGH POLISHED SS JACKETED REACTOR FV 45 PSI

Stock no. E-4610 100 gallon HIGH POLISHED SS JACKETED REACTOR FV 45 PSI Inox serial no. 99014-2, yr 1999. OIN 5.1088783, CRN 15452.5 Shell rated for Full Vacuum/45 psi @ 300 deg. F to 32 deg. F Side dimple jacket rated for 45 psi @ 300 deg. F to 32 deg. F. U stamped. Made […]

60 gallon HIGH POLISHED SS JACKETED REACTOR FV 45 PSI

Stock no. E-4609 60 gallon HIGH POLISHED SS JACKETED REACTOR FV 45 PSI Inox serial no. 97012-2, yr 1997. OIN 5.1017139, CRN L2289.5 Shell rated for Full Vacuum/45 psi @ 300 deg. F to 32 deg. F Side dimple jacket rated for 45 psi @ 300 deg. F to 32 deg. F. U stamped Second […]

200 gallon GROEN STAINLESS STEEL JACKETED KETTLE

Stock no. E-4616 (2) 200 gallon GROEN STAINLESS STEEL JACKETED KETTLE No. 17738.  Jacket rated for 100 psi 48 inch diameter x 36 inch deep Has a 2.5 inch threaded bottom outlet. Open top Side and bottom jacket fittings (2) available

150 gallon GROEN STAINLESS STEEL JACKETED KETTLE

Stock no. E-4613 150 gallon GROEN STAINLESS STEEL JACKETED KETTLE Model N150 SP, no. 26396 A. Jacket rated for 40 psi 42 inch id x 34 inch deep. Hinged Lid Has a 2.5 inch threaded bottom outlet Side and bottom jacket fittings On 3 legs. Bottom center outlet 21 inch to ground To be cleaned […]

GRACO T2 STAINLESS STEEL DRUM TRANSFER PUMP

Stock no. P-3395 GRACO T2 STAINLESS STEEL DRUM TRANSFER PUMP Model 295616, serial no. A003106, series CO8. 2:1 ratio Stainless steel contacts. Has 2.25 inch threaded fitting for a drum 34 inch long below fitting, 54.5 inch o/a height Max air working pressure is 180 psi Max fluid working pressure is 405 psi Pump has […]

1000 gallon STAINLESS STEEL FOOD GRADE TANK

Stock no. A-5614 1000 gallon STAINLESS STEEL FOOD GRADE TANK Cherry Burrell model E, serial no. 68-650-2 65 inch diameter x 70 inch straight side with dished bottom Has slip in 2 piece lid and small top bridge 3 inch bottom center tri-clamp outlet, (2) 2 inch top inlets on bridge Bottom thermal well. (4) […]

50 gallon GROEN STAINLESS STEEL JACKETED KETTLE

Stock no. E-4608 50 gallon GROEN STAINLESS STEEL JACKETED KETTLE Model GPT 50 SP, National Board no. 28753, year 1965 Jacket rated for 25 psi @ 300 deg. F. U Stamped 36 inch id x 20 inch deep. 35.5 inch o/a height 1.5 inch bottom center > side outlet. (3) jacket fittings, top one with […]

1.5 inch WILDEN POLY DIAPHRAGM PUMP

Stock no. P-3389 (2) 1.5 inch WILDEN POLY DIAPHRAGM PUMP Has 1.5 inch flanged inlet and outlet Air powered To be cleaned and tested prior to shipping (2) available

150 gallon STAINLESS STEEL JACKETED TANK SLANT BOTTOM

Stock no. E-4602 (5) 150 gallon STAINLESS STEEL JACKETED TANK SLANT BOTTOM 36 inch x 36 inch with slant bottom, open top, Has bracket for mixer Side is insulated and side jacketed Also has electric tube type heaters for the bottom (unsure if in working order) Has 1.5 inch side outlet. Last used for candle […]

600 gallon STAINLESS STEEL JACKETED HORIZONTAL TANK

Stock no. E-4601 (2) 600 gallon STAINLESS STEEL JACKETED HORIZONTAL TANK Mfg. by Mueller, plate needs cleaning to read 60 inch wide x 92 inch long x 37.5 inch deep with hinged lids Has 1.5 inch end outlet. End jacket fittings Recently used for melting wax (2) available. SALE PENDING  

470 mm LANCO FILTER PRESS with CENTER FEED POLY PLATES

Stock no. C-2787 470 mm LANCO FILTER PRESS with CENTER FEED POLY PLATES Lanco 2/2-4M, F1113. Expandable to 4 cu. ft. Has 470 mm (approx. 40) gasketed poly plates with 2 inch center feed, (4) 1.5 inch corner outlets Setup with 41 inch of work space and can be converted to longer work space. Has […]

DUAL ZONE 18 KW STERLING HOT OIL HEATER 480 V 550 DEG. F G2026-M0

Stock no. G-4033 DUAL ZONE 18 KW STERLING HOT OIL HEATER Model G-2026-M0, serial no. 33E5500 18 Kw each side rated to 550 deg. F, 100 psig 2 Hp pump each side. 2 sets of rear return and delivery fittings 480 v, 3 ph, 49.8 FLA, motor FLA 3.1, 115 v controls SELLING AS IS […]

4.8 cu. ft. SANYO GALLENKAMP PLUS II 300 DEG. C OVEN 120 V

Stock no. G-4030 4.8 cu. ft. SANYO GALLENKAMP PLUS II OVEN with Chart Recorder Model Plus II, cat. no. OPL150.TS1.8, serial no. SG93/06/717 Made in the UK. 110/120 volt, 60 hz, 2065 watts Has analog safety thermostat control to 300 deg. C Honeywell Truline Chart Recorder Stainless steel interior measuring 18 x 18 x 25.5 […]

3.8 sq. ft. U TUBE STAINLESS STEEL HEAT EXCHANGER

Stock no. G-4027 3.8 sq. ft. U TUBE STAINLESS STEEL HEAT EXCHANGER Allegheny Bradford serial no. 10770-1-1, National Board no. 2297, year 2002 Repaired in 2018 by the mfg. and looks to be unused since. Labeled Water Heater and Steam Shell and tubes rated for FV and 150 psi @ 350 deg. F to -20 […]

4 x 16 inch CARBON STEEL BASKET FILTER 1.25 inch fittings

Stock no. C-2786 4 x 16 inch CARBON STEEL BASKET FILTER 1.25 inch fittings 3.5 x 11.5 inch stainless steel filter basket. 4.5 inch diameter x 16 inch housing 1.25 inch threaded side inlet , side outlet, bottom drain 1/4 inch top vent and (2) on the side, plus a 1/2 inch side out Clamped […]

100 gallon STAINLESS STEEL JACKETED REACTOR TANK with MIXER

Stock no. E-4599 100 gallon STAINLESS STEEL JACKETED REACTOR TANK with MIXER APV Crepaco serial no. E-6592, year 1988, National Board no. 7123 Rated for 45 psi @ 300 deg. F Shell and Jacket Side Jacket re-certified to 75 psi @ 300 F in 1998 by Cotter Corp, 1 inch in and out Approximately 30 […]

NESLAB CFT 33 LIQUID CHILLER RECIRCULATOR 950 WATTS

Stock no. G-4012 NESLAB CFT 33 LIQUID CHILLER RECIRCULATOR Model CFT-33, sn 92AML10020-1, pn 34B103030200 Rated for 950 watts cooling at 60 hz 115 volt, 1 phase, 60 hz, 12.4 amp PD-1 pump, 1.1 gallon reservoir. 3/4 inch supply and return connections Last used with a Spectrometer (1) available

2 inch FRISTHAM SANITARY SS CENTRIFUGAL PUMP 15 HP

Stock Number: P-2704 2 inch FRISTHAM SANITARY SS CENTRIFUGAL PUMP Mfg. Fristham Pumps Model FP3532-140, s/n FSP3532013497 15 Hp, 3450 rpm, 208-230/460v, 3ph 2 inch outlet, front cover with inlet missing (1) available

2.5 x 3 inch FRISTHAM SANITARY SS CENTRIFUGAL PUMP 10 HP

Stock Number: P-2703 2.5 x 3 inch FRISTHAM SANITARY SS CENTRIFUGAL PUMP Mfg. Fristham Pumps Model FP 3551-215, s/n FP355198232 10 Hp, 1755 rpm, 230/460v, 3ph 2.5 x 3.5 inch in and out with an additional 1 inch port (1) available

2900 WATT POLYSCIENCE LIQUID CHILLER

Stock no. G-4037 (3) 2900 WATT POLYSCIENCE LIQUID CHILLER Model N0772046 6160T21E4Q1N, serial 1B11A0222 2900 watt @ 20 deg. C, working temp -10 to +40 C 1 Hp Turbine pump. R134A refrigerant 230 v, 1 ph, 60 hz, 12.2 amp 1/2 inch return, supply, and drain 1.1 gallon reservoir. Compares to updated model 6160T21A130D (3) […]

AMETEK ROTRON 1 PH BLOWER 027084 115/230v

Stock no. G-4008 AMETEK ROTRON 1 PH BLOWER part no. 027084 3125 rpm, 115/230 v, 1 ph, 1.8/0.9 amp Has 4.5 inch side inlet (same as squirrel cage id) and 3 x 3 1/8 inch outlet Large quantity just in, UNUSED Will sell by the piece or entire lot, 2 full boxes

SOLID STATE COOLING SYSTEMS CHILLER TCUBE EDGE 230 WATT

Stock no. G-4009 SOLID STATE COOLING SYSTEMS CHILLER UPGRADE KIT Model TCube Edge, part no. 10-14072-2A-0-A4-AF-05 Serial no. 8403334 Rated for 230 watt @ 20 deg. C, Range 0 deg. C to 65 deg. C Pump flow rate to 3 lpm @ 14 psig (adjustable) 1 liter tank volume. Spec sheet with curve on file. […]

AMETEK POWER CONDITIONER ABC2000-2S

Stock no. G-4010 AMETEK POWER CONDITIONER Model ABC2000-2S, part no. 95083-14R, mfg. Powervar, Waukegan, IL 208/240 v, 9.5/8.5 amp input 120/240 v, 8.3/8.3 amp output, both at 60 Hz (1) available

EASYVAC 7 SINGLE STAGE VACUUM PUMP 6.0/7.0 CFM

Stock no. P-3376 EASYVAC 7 SINGLE STAGE VACUUM PUMP Across International model EasyVac-7, serial no. 7E180504, 11/2018 Rated for 150 microns total pressure, 6.0/7.0 cfm, single stage 110/220 volt, 1 phase, 50/60 Hz, 370 watts LOOKS UNUSED! (1) available  

SOGEVAC SV 40 BI OIL SEALED VACUUM PUMP 1.5 KW

Stock no. P-3368 (8) SOGEVAC SV 40 BI OIL SEALED VACUUM PUMPS Model SV40 BI 960331V3010, 960363VBIEC3E04B3A2C all rated for 1.5 Kw, 200-240 v, 50/60 Hz, 1 ph Pumping speed (60 Hz): 48 m³/h, Ultimate pressure: 0.05 mbar (8) similar available, years 2010 to 2016.

WAUKESHA MODEL 34 STAINLESS STEEL DISPLACEMENT PUMP

Stock no. P-3367 WAUKESHA MODEL 34 STAINLESS STEEL DISPLACEMENT PUMP Serial no. 101253 2 Hp vari-drive, 1725 rpm in, 230/460 v, 3 ph, 60 hz with 10.9 to 100 rpm output Has a threaded 1.5 inch top fitting with a 2 inch tri-clamp adapter Bottom outlet is 2 inch dairy thread Mounted on a SS […]

1/2 Hp LIGHTNIN MIXER ND2 GEAR REDUCED

Stock no. B-4419 1/2 Hp LIGHTNIN MIXER GEAR REDUCED Model ND2, serial no. 735911 1/2 Hp, 1725 rpm, 230/460 v, 3 ph, 60 hz Gear reduced, 350 rpm shaft speed Currently setup with a 4-bolt mount It can also be clamp mounted. Includes 3/4 inch diameter stainless steel shaft and prop (1) available

Stainless Steel Double Ribbon for a 150 cu. ft. Ribbon Blender

Stock no. B-4428 Stainless Steel Double Ribbon for a 150 cu. ft. Ribbon Blender Believed to be for a Young Ribbon Blender 54 inch od outer ribbon diameter, 36.5 inch od inner ribbon Center shaft is 7 inch diameter x 114.75 inch long with 149 inch overall length Ends are 4.5 inch diameter with one […]

SIHI LEMR 110 AZ AAA OA O AW LIQUID RING VACUUM PUMP 76 cfm

Stock no. P-3364 SIHI LEMR-110-AZ AAA OA O AW SINGLE STAGE LIQUID RING VACUUM PUMP Serial no. CA 1349615-01. Stock no. 10117336. Made in Canada. Rated to 76.5 cfm at 1725 rpm 5 HP, 1725 rpm, 208-230/460V, 60 Hz, 3-phase (also rated for 50 Hz, 190/380V, 4.2 HP). 1.5 inch fittings. Overall dimensions: 36 in. […]

AMPCO 2.5 X 2 DC2 STAINLESS STEEL CENTRIFUGAL PUMP 10 HP

Stock no. P-3363 AMPCO 2.5 X 2 DC2 STAINLESS STEEL CENTRIFUGAL PUMP 10 HP Model 2 1/2 x 2 DC2, serial no. AA-9518-1-20 2.5 inch inlet x 2 inch outlet tri-clamp fittings, 6 3/8 inch impeller 10 Hp, 3485 rpm, 230/460 volt, 3 ph Curve on file, used for cleaning/sanitary solutions (1) available

FLATPLATE 316L SS HEAT EXCHANGER FP 10×20-120/2p

Stock no. G-4005 FlatPlate 316L SS HEAT EXCHANGER FP 10×20-120/2p FP Series Model 131007103, serial no. H120CC07109019, date 9-03-20 Rated to 450 psi @ 350 deg. F. 316L Stainless Steel plates, copper brazed Side A volume = .505 cu. ft. side B = .514 cu. ft. (4) 2 inch MPT fittings, 120 plates, 9.8 inch […]

YAMATO GLASS 10 LITER ROTARY EVAPORATOR RE-71

Stock no. G-4004 Yamato model RE-71 Glass 10 liter Rotary Evaporator Serial no. A14002, 220 volt input, 50 hz, 15 amp Motor for rotating is 40 watts max output, 100 v, 50/60 hz, 1 amp Base vessel is 10 inch diameter and sits on a heating mantle Top column is approximately 6.5 inch diameter x […]

26 gallon/100 liter POLISHED STAINLESS STEEL TANK ON WHEELS

Stock no. A-5609 26 gallon/100 liter POLISHED STAINLESS STEEL TANK Allegheny Bradford Corp. serial no. 035820-1-1-1 Print no. VF480500. 100 liter capacity 18 inch id x 27 inch with dished bottom Has slip on top with 2 hinged lids , 1.5 inch bottom center diaphragm valve 4 legs on wheels, 51 inch to top rim […]

Techne FTU20DPC TU-20D Thermoregulator, -40°C to +200°C for bath chiller

Stock no. G-4002 Techne FTU20DPC TU-20D Thermoregulator, -40°C to +200°C for bath chiller 120 volt, 50/60 hz, 1500 watt • Excellent temperature stability: ±0.005°C at 40°C • 1.8kW heater power for fast heat up • 4 digit setting with a bright LED digital temperature display • This unit incorporates an RS232 connection • User adjustable […]

MILLIPORE MOBIUS MIX500 SYSTEM 500 liter POLY VESSEL

Stock no. A-5608 MILLIPORE MOBIUS MIX500 SYSTEM 500 liter POLY VESSEL Catalog no. MIX0500LG05, 500 liter poly tank on wheels 35 inch diameter x 38 inch with dished bottom and open top It has a side door with a sight glass and a rectangular opening under There are (2) round openings in the bottom with […]

33 gallon 316 STAINLESS STEEL PRESSURE TANK 95 PSI

Stock no. E-4594 33 gallon 316 STAINLESS STEEL PRESSURE TANK with bottom outlet Alloy Products sn 24307-006, 1986, repaired by Carter Corp 10-90, no. 2187 Rated for 95 psi @ 250 deg. F to -20 F 18 inch diameter x 30 inch with dished bottom and top This has a 1 inch tri-clamp bottom center […]

33 gallon 316 STAINLESS STEEL PRESSURE TANK 98 PSI

Stock no. E-4594 33 gallon 316 STAINLESS STEEL PRESSURE TANK with bottom outlet Certified for Pope Scientific by Alloy Products Rated for 98 psi @ 100 deg. F to -20 F 18 inch diameter x 30 inch with dished bottom and top This has a 1 inch bottom center outlet elbowed to the side. It […]

100 gallon LEE STAINLESS STEEL JACKETED SWEEP KETTLE 90 PSI

Stock no. E-4597 100 gallon LEE STAINLESS STEEL JACKETED SWEEP KETTLE Lee Metal Products serial no. 826N, date 9/61 Jacket rated for 90 psi @ 330 deg. F and has been pressure tested 38 inch inside diameter x 30 inch deep with a 1.5 inch bottom center outlet Sweep agitator currently with a hydraulic drive, […]

40 HP STAINLESS STEEL TANK MOUNT DISPERSER

Stock no. B-4418 40 HP STAINLESS STEEL TANK MOUNT DISPERSER 40 Hp tank mounted disperser to be assembled. It will consist of the following: Unused 40 Hp, 460 volt motor setup with a multi-belt drive/pulley and guards The unused shaft is 4 inch diameter x 76 inch outside of the mount It will include a […]

2.75 gallon 316 STAINLESS STEEL PRESSURE TANK FV/50 PSI

Stock no. E-4592 2.75 gallon 316 STAINLESS STEEL PRESSURE TANK Alloy Products serial no. 111494-001, year 2002 National Board stamped, no. 1223 Rated for Full vacuum and 50 psi @ 350 deg. F to -20 F 9 inch diameter 10.5 inch with dished bottom and top. Has tri-clamp fittings, 3 inch top center inlet, (2) […]

2.5 inch WAUKESHA SS DISPLACEMENT PUMP MODEL 060

Stock no. P-3358 2.5 inch WAUKESHA SS DISPLACEMENT PUMP Model 060, serial no. 310438 02 Has 2.5 inch tri-clamp fittings Came in with a 10 Hp motor coupled to a 7.74-1 gear reducer Motor is 330/575 v, 3 ph and can be changed out  

300 gallon STAINLESS STEEL CONE BOTTOM TANK

Stock no. A-5600 300 gallon STAINLESS STEEL CONE BOTTOM TANK 38 inch diameter x 60 inch straight side with 3 inch cone bottom Open top. 1.5 inch bottom center outlet, 1.25 inch side inlet and outlet Legs can be shortened if needed. Total height is 108 inch Last used for cleaning products (1) available

650 gallon STAINLESS STEEL INSULATED TANK with mixer

Stock no. A-5610 650 gallon STAINLESS STEEL INSULATED TANK with slant bottom Approx. 60 inch inside diameter x 64 inch to bottom of outlet with slant bottom Has offset coned top with top manway. (2) 4 inch sani-thread top inlets, 3 inch sani-thread side outlet. (2)side fittings Top center mounted mixer with a single straight […]

8 quart STAINLESS STEEL TWIN SHELL DRY BLENDER PK

Stock no. B-4417 8 quart STAINLESS STEEL TWIN SHELL DRY BLENDER Paterson Kelley number LB 10944, rated for 300 lbs per cu. ft. Single phase 115-230 volt, 1/4 Hp, 1725 rpm motor gear reduced. Mounted on ss wheeled cart O/a 31 x 22 x 50 inch tall with bottom up 7 3/8 inch id top […]

COWLES 5 gallon JACKETED STAINLESS STEEL DISPERSER with SWEEP

Stock no. B-4416 COWLES 5 gallon JACKETED STAINLESS STEEL DISPERSER with SWEEP Model VISCO MAX  VML 5, serial no. LA-643, p/n 460539, 6/2000 Coated stainless steel jacketed bowl, 14 inch id x 13 inch deep, flat bottom Bowl has a 2 inch side outlet and there is a side jacket inlet and outlet Dual controls […]

BRAWN 3/4 HP VERTICAL DOWN MIXER

Stock no. B-4415 BRAWN 3/4 HP VERTICAL DOWN MIXER Model BGMF75, serial no. 040198 3/4 Hp, 850 rpm, 230/460 v, 3 ph Gear reduced. Stainless steel flange mount for shaft 4-bolt square mount for mixer. (1) available

2.5 gallon 316 STAINLESS STEEL PRESSURE TANK 140 PSI

Stock no. E-4572 (7) 2.5 gallon 316 STAINLESS STEEL PRESSURE TANK 140 PSI Alloy Products mfg. in 1994 Rated for 140 psi @ 100 F to -20 F 9 inch diameter 8 inch with dished bottom and top. 22 inch o/a height Has threaded fittings, (4) 1/4 inch on top and (1) bottom center outlet […]

40 liter 10 gallon JACKETED PRESSURE MIX TANK

Stock no. E-4571 40 liter 10.5 gallon JACKETED PRESSURE MIX TANK Mfg. by Klockner Ferromatik Desma GMBH of Germany Serial no. 3121, year 1988. Stamped 40 liter internal capacity It is rated for 4 bar/58 psi @ 100 C/212 F 14 inch inside diameter x 16 inch on the straight side with a dished bottom […]

7.5 Hp STAINLESS STEEL HOMOGENIZER MIXER 31 inch shaft

Stock no. B-4412 7.5 Hp STAINLESS STEEL HOMOGENIZER MIXER 31 inch shaft Joshua Greaves and Sons (UK) Greaves mixer type GM-5, s/n 16186 30.5 inch shaft, 6.5 inch od stator, 4 inch rotor, 62 inch o/a 7.5 Hp (5.5 Kw), 3600 rpm, 230 v, 3 ph, 3.2 a 4-bolt mount on 22 inch diameter stainless […]

5 HP DISPERSER TANK MOUNT HIGH SHEAR MIXER 32 inch shaft

Stock Number: B-4413 5 HP DISPERSER TANK MOUNT HIGH SHEAR MIXER IKA Works Ultra-Turrax type MSM-100, s/n 1923 5 Hp, 3550 rpm, 208-230/460v, 3ph, 60hz, TEFC Stainless steel 32 inch long shaft with 4 inch chopper blade Has separate fixed shaft with female thread end, possibly for a baffle 4-bolt mount on 22 inch diameter […]

GAST .42 HP STAINLESS STEEL FLANGE MOUNT AIR POWERED MIXER

Stock no. B-4410 (2) GAST .42 HP STAINLESS STEEL FLANGE MOUNT AIR POWERED MIXER Air motor model 1AM-NCC-11 rated for .42 hp 10,000 rpm max., 100 psi max. Came in with a square shaft coupling, but we will convert to round with a Stainless Steel shaft and a prop. (2) available

6 GALLON STAINLESS STEEL TANK ON WHEELS

Stock no. A-5580 (2) 6 GALLON STAINLESS STEEL TANK ON WHEELS 15.5 inch inside diameter x 7.5 inch straight side with a dished bottom has a clamp on flat top with a 3/4 inch center hole there is a 3/4 inch tri-clamp bottom center outlet Polished sanitary stainless steel. 3 legs on wheels (2) available

CLEVELAND FGLX 1.2 VERTICAL DOWN MOUNT MIXER 1.5 HP

Stock no. B-4407 (2) CLEVELAND 1.5 HP VERTICAL DOWN MOUNT MIXER Model FGLX 1.2 1.5 Hp, 1725 rpm, 145TC frame, 4.94-1 gear reduced Motor to be replaced, so choice of voltage is open Takes a 1.25 inch diameter shaft. Stainless steel shaft and prop included. (2) available

LIGHTNIN X5P25 CLAMP MOUNT MIXER 1/4 HP 3 PH

Stock no. B-4406 LIGHTNIN 1/4 HP CLAMP MOUNT MIXER Model X5P25, serial no. R03415539-02 .25 Hp, 1725 rpm, 230/460 v, 3 ph direct drive Currently with bolt on mount, clamp mount is available. Comes with stainless steel shaft and prop (1) available

245 gallon STAINLESS STEEL FLAT BOTTOM TANK

Stock no. A-5583 245 gallon STAINLESS STEEL FLAT BOTTOM TANK 42 inch outside diameter x 41.5 inch deep, flat bottom and top Has a 3/4 inch threaded top inlet and side inlet. A 15 x 12 inch hatch, 8.75 inch top opening and a 3 inch top opening that goes 3/4 the way into the […]

GIRTON 200 GALLON SS DELUXE JACKETED FARM TANK 12-200

Stock no. E-4568 GIRTON 200 GALLON STAINLESS STEEL DELUXE FARM TANK Model 12-200, serial number 210119 Sanitary stainless steel with a jacket for cooling 49.75 inch x 43.5 inch x 23.5 inch deep inside dimensions It has 4.5 inch thick walls and is mounted on wheels Has a 1.5 inch side outlet with dairy threads […]

45 gallon POLISHED STAINLESS STEEL PORTABLE TANK

Stock no. A-5582 45 gallon POLISHED STAINLESS STEEL PORTABLE TANK Mfg. by Tech Nova Systems of Canada, PO726-5 24.75 inch id x 19 inch straight side with 7 inch slant cone bottom has flat clamp on lid with a 6 inch top center inlet with a sight glass (2) 2 inch and (2) 2 inch […]

30 Liter 316L SS REACTOR PRECISION STAINLESS VACUUM 45-100 PSI

Stock no. E-4567 30 Liter 316L SS REACTOR PRECISION STAINLESS VACUUM 45-100 PSI Serial no. 9100-9, year 1995, National Board no. 5968 Shell rated for 15 psi vacuum and 45 psi @ 350 deg. F Side Only Jacket rated for 100 psi @ 350 deg. F 10 inch inside diameter x 24 inch straight side […]

1/2 Hp AIR POWERED CLAMP MOUNT MIXER JWI

Stock no. B-4182 1/2 Hp AIR POWERED CLAMP MOUNT MIXER JWI model JLA50, gear reduced Approximately 350 rpm output max Takes bolt on shaft which we can make to order (1) available

Large Antique Balance Gold Apothecary Scale Glass Wooden Case

Large Antique Balance Gold Apothecary Scale Glass Wooden Case Balance scale measures 48 inch x 22.5 inch x 54 inch tall Cabinet measures 60 inch x 32 inch x 83 inch Weighing platforms are 16 inch diameter Late 1800’s from a Gold Assayer Front cabinet door lifts upwards. Balance has leveling feet.

5 inch 316 STAINLESS STEEL 4-BLADE AGITATOR HUB

Stock no. G-3994 5 inch 316 STAINLESS STEEL 4-BLADE AGITATOR HUB Stamped Z-19502-007 5 inch inside diameter, keyed with set screw Takes 4-bolt blades, not included but can be made to order. (1) available WE HAVE OTHER SIZE HUBS WITH OR WITHOUT BLADES AVAILABLE

50 cu. ft DOUBLE CONE BLENDER CARBON STEEL

Stock no. B-4401 50 cu. ft DOUBLE CONE BLENDER CARBON STEEL 66 inch diameter x 16 inch straight side 25 inch bottom cone and 30 inch top cone Approximately 50 cu. ft. volume with 5 Hp motor (plate needs to be cleaned) Belt drive to gear reducer 12 inch bottom outlet with 5 inch valve […]

1/2 Hp CHEMINEER FLANGE MOUNT MIXER 430 RPM

Stock no. B-4400 1/2 Hp CHEMINEER FLANGE MOUNT MIXER Model VLA-5, serial no. 1-23006-8 1/2 Hp, 1750 rpm, 230/460 v, 3 ph, 60 hz Gear reduced to 430 RPM Includes stainless steel shaft and prop (1) available

20 Hp 8 X 6 MOYNO PROGRESSIVE CAVITY PUMP 2G0HS1 CSB-X AAALF

Stock no. P-3345 (2) 20 Hp 8 X 6 MOYNO PROGRESSIVE CAVITY PUMP Model 2G0HS1 CSB-X AAALF, serial no. AS37292-10 (and AS37292-11) This one has a 8 inch top inlet and a reducer to 6 inch end outlet Second one has a side inlet Comes with a belt drive 20 Hp, 1160 rpm, 230/460 volt, […]

1 liter JAYGO STAINLESS STEEL HIGH INTENSITY MIXER GRANULATOR

Stock no. B-4395 1 liter JAYGO COSMAIR STAINLESS STEEL HIGH INTENSITY MIXER GRANULATOR. Novamix 1 liter, model NX1, serial no. 2589, year 1996 3.5 inch diameter x 5 inch straight side with dished bottom, hinged lid Has bottom center impeller, variable speed 350-3000 rpm, 0.55 Kw Side chopper breaker blade, variable speed 600-6000 rpm, 0.18 […]

POLYTRON PT-MR2100 LAB HOMOGENIZER MIXER

Stock no. B-4394 POLYTRON PT-MR2100 LAB HOMOGENIZER MIXER Made in Switzerland by Kinematic AG, serial number 656043 Stainless steel contacts, 7/16 inch diameter x 5 3/8 inch barrel Variable speed, 500 watts, 110 volt, 50-60 Hz Tested in good working condition Currently without a stand, but we may have something to fit. (1) available

PRESSURIZED HUMIDITY TEST SYSTEM HAST 1000F EXPRESS TEST

Stock no G-3977 PRESSURIZED HUMIDITY TEST SYSTEM 57 psi Express Test Corp model HAST 1000F, Highly Accelerated Stress Test Systems Serial no. 42891, date 8/2009 Polished stainless steel components, rated for 57 psi 220 vac, 5.5 kva, 30 amp, 60 hz, single phase. Labeled 208 v This model can accommodate 12 single width or 6 […]

5600 Btu/Hr LYTRON RECIRCULATING WATER COOLED CHILLER

Stock no. G-3980 5600 Btu/Hr LYTRON RECIRCULATING WATER COOLED CHILLER Model RC011G03BB2C007, serial no. 828488-02 (now Boyd Co.) 115 v, 1 ph, 60 Hz, 15.4 a, 1650 watts. Digital controls 2 gallon capacity reservoir with front water level tube. 1.3 gpm pump Supply and return connections in the rear. Approximately 15 x 25 x 27 […]

482 deg. F. 1.15 cu. ft. BLUE M OVEN MODEL DCC-146C

Stock no. G-3976 482 deg. F. 1.15 cu. ft. BLUE M OVEN MODEL DCC-146C Serial no. DCC-442, BOM C8-00001. Rated to 250 deg. C/428 deg. F. 208-240 v, 1 ph, 60 hz. L1 = 14/16 a, L2 = 14/16 a 10.5 x 14 x 13.5 inch internal dimensions. O/a 29 x 31 x 80 inch […]

100 gallon INSULATED FIBERGLASS TANK

Stock no. A-5569 100 gallon INSULATED FIBERGLASS TANK 25 inch inside diameter x 48 inch straight side, 61 inch o/a height Flat bottom and domed top All fittings are flanged, 8 inch top center, 2 inch side inlet, (2) 1/2 inch side inlets and (1) side outlet. 1.25 inch side outlet (1) available

95 gallon INSULATED FIBERGLASS TANK FLAT BOTTOM

Stock no. A-5568 95 gallon INSULATED FIBERGLASS TANK 24 inch inside diameter x 48 inch straight side, 61 inch o/a height Flat bottom and domed top All fittings are flanged, 12 inch top center, 4 inch side inlet, 1 inch side inlet. (2) 1/2 inch side inlets and side outlets. 1.25 inch side outlet (1) […]

200 gallon FIBERGLASS TANK FLAT BOTTOM with METERING PUMPS

Stock Number: A-4058 200 gallon FIBERGLASS TANK FLAT BOTTOM with METERING PUMPS Mfg. NE Plastic Coated Products 3 ft. x 45 in., flat bottom and top w/lid 1 inch side outlet, 1.5 inch top inlet Ultra sonic level control, skid mounted With  N-feeder solenoid type metering pumps Used with NaOH, Sodium Hydroxide Solution (1) available

.50 inch PLASTIC DIAPHRAGM PUMP

Stock no. P-3336 .50 inch PLASTIC DIAPHRAGM PUMP No plate 1/2 inch threaded in and out with optional end fittings (plugged) Air powered (1) available

1 inch POLY DIAPHRAGM PUMP PLATING INTERNATIONAL

Stock no. P-3337 1 inch POLY DIAPHRAGM PUMP PLATING INTERNATIONAL Inc. model P125PP-PP-TF-TF-PP, YR. 2017 1 inch flanged > threaded fittings Air powered, 8.4 bar max. Rated to 157 lpm (41.4 gpm) (1) available

8 quart POLYCARBONATE TWIN SHELL DRY BLENDER PK

Stock no. B-4392 8 quart POLYCARBONATE TWIN SHELL DRY BLENDER PK Paterson Kelly number LB 8047 (2) 8 inch diameter x 12 inch deep chambers. O/a 38 x 17 x 23 inch Single phase 115 v fractional Hp motor Chain drive (1) available

300 Liter 316L Stainless Steel Jacketed Cryo Vessel 45-65 psi

Stock no. E-4559 (3) 300 Liter 316L Stainless Steel Jacketed Cryo Vessel 45-65 psi Sartorius Stedim Biotech, Model CV-00000-0155, Yr. 2007 National Board stamped Shell rated for 45 psi @ 280 F., MDMT -112 F@ 45 psi, MAEWP +15 psi Dimple jacket rated for 65 psi @ 280 F. Internal jacketed baffles on lid for […]

7 x 28 inch 304L STAINLESS STEEL BASKET FILTER 2 inch fittings

Stock no. C-2780 7 x 28 inch 304L STAINLESS STEEL BASKET FILTER 2 inch fittings Parker model 9502-0020-UM/4LFB 12-2, serial no. 253468, yr. 2006 Rated for 151 psi @ 450 deg. F, 201 psi @ 100 deg. F and to -20 deg. F 7 x 28 inch stainless steel filter basket. 8 inch diameter x […]

7 x 28 inch ALUMINUM BASKET FILTER 1 inch fittings

Stock no. C-2778 7 x 28 inch ALUMINUM BASKET FILTER 1 inch fittings No plate 7 x 28 inch stainless steel filter basket. 8 1/4 inch diameter x 32 inch housing 1 inch side inlet and bottom outlet (2) 1/4 inch top fittings with vent and gauge. Legs/stand included Last used for BioDiesel (1) available

7 x 28 inch ALUMINUM BASKET FILTER 2 inch fittings

Stock no. C-2779 7 x 28 inch ALUMINUM BASKET FILTER 2 inch fittings No plate 7 x 28 inch stainless steel filter basket. 8 1/4 inch diameter x 32 inch housing 2 inch threaded > 1 inch side inlet and bottom outlet (2) 1/4 inch top fittings with vent and gauge. Legs/stand included Last used […]

7 x 28 inch CARBON STEEL BASKET FILTER 2 inch fittings ROSEDALE

Stock no. C-2776 (2) 7 x 28 inch CARBON STEEL BASKET FILTER 2 inch fittings ROSEDALE Products model M0813-2P-1-150-C-V-70V-P 7 x 28 inch stainless steel filter basket. 8 3/8 inch diameter x 38 inch housing 2 inch threaded > flange side inlet and bottom outlet 1/4 inch top vent and (2) on the side. 1 […]

18.8 sq. ft. SS SHELL and TUBE HEAT EXCHANGER 4 pass

Stock G-3966 18.8 sq. ft. SS SHELL and TUBE HEAT EXCHANGER 4 pass Thermal Products Inc. serial no. 19103, yr. 2019, NB no. 3332 Certified by JPD Tube and Coil, model BBM 08×36 04 Shell and tubes rated for 150 psi @ 375 deg. F and -20 deg. F Stainless steel tubes and head, carbon […]

10 HP PHILADELPHIA 3803 SPTN RIGHT ANGLE DRIVE MIXER 125 RPM

Stock Number: B-2289 10 HP PHILADELPHIA RIGHT ANGLE DRIVE MIXER Mfg. Philadelphia Model 3803 SPTN, serial no. 83DBE0871 14-1 ratio, 125 rpm. Originally with 2 speed motor Flange mount with place for a seal (none currently with) Buy with or without motor setup (1) available

30 Hp CHEMINEER RIGHT ANGLE DRIVE 30:1 RATIO

Stock no B-3599 30 Hp CHEMINEER RIGHT ANGLE DRIVE Missing plate. Output speed ratio 30 to 1 (need to confirm) Will sell with or without a motor setup Shaft and blades are optional (1) available

30 Hp CHEMINEER RIGHT ANGLE DRIVE 3-HSNS-30

Stock no B-3598 30 Hp CHEMINEER RIGHT ANGLE DRIVE Model 3-HSNS-30, missing plate Output speed to be determined Will sell with or without a motor setup Shaft and blades are optional (1) available

STAINLESS STEEL ROTARY STRAINER WITH 4 INCH FLANGES

Stock no. C-2774 STAINLESS STEEL ROTARY STRAINER WITH 4 INCH FLANGES Compares to a Merco Dorr Oliver MRS model. ID plate is missing Housing is 10 inch diameter on the top and goes to 14 inch diameter It is 22 inch on the straight side and has a flat bolted top There is a dish […]

8.5 x 22.5 inch CUNO STAINLESS STEEL FILTER HOUSING 5.5 gallon

Stock no. C-2541 8.5 x 22.5 inch CUNO STAINLESS STEEL FILTER HOUSING 8.5 x 22.5 inch inside dimensions with clamped top 1.5 inch top inlet and outlet with a 1/4 inch drain There are no obstructions or brackets inside, smooth finish. Sell with or without stand (1) available

1 inch 316l/316 STAINLESS STEEL MICRO MOTION MASS FLOW SENSOR

Stock no. G-3962 1 inch 316l/316 STAINLESS STEEL MICRO MOTION MASS FLOW SENSOR Model DS100S128SU, serial no. 204448, type 5, factor 06667 Rated for -240 to 204 deg. C., flow cal factor 66.6715.13 dens cal factor 11868131454.44, tube 2250 psig, conn 275 psi 1 inch flanged inlet and outlet, 17 x 29 x 24 inch […]

2 inch VIKING HEAVY-DUTY ABRASIVE LIQUID GEAR PUMP K4625

Stock no. P-3323 2 inch VIKING HEAVY-DUTY ABRASIVE LIQUID GEAR PUMP Cast Iron, Model K4625, serial no. 11463264 with relief valve 2 inch threaded fittings, mechanical seal 25 gpm nominal rating at 280 rpm to 400 psig Rated for 1 to 3 Hp. Will sell with or without a drive setup (1) available

1/4 Hp KINETIC DISPERSION HIGH SPEED VERTICAL DOWN MIXER

Stock no B-3181 (2) 1/4 Hp KINETIC DISPERSION HIGH SPEED VERTICAL DOWN MIXER Model DEMO7 1/4 Hp, 1725 rpm motor, 208-230/460 v, 3 ph 1.5-1 ratio, 1150 rpm shaft output Selling mixer only, tank in picture no longer available (2) available

8 cfm KINNEY VACUUM PUMP KC 8

Stock no. P-2848 8 cfm KINNEY VACUUM PUMP KC 8 Kinney Vacuum Division/Tuthill,  model KC 8, 802497-0 810 72 H581.5 Rated for 8 cfm 1/2 inch inlet 1 ph, 115/230 v, 1/3 hp, 1725 rpm (1) available SALE PENDING  

3 HP ROTARY SCREENER 10 X 24 SCREEN CLASSIFIER

Stock no. C-2771 3 HP ROTARY SCREENER with 10 X 24 SCREEN CLASSIFIER Carbon steel shell with stainless steel agitator and screw feed takes an approximate 10 inch diameter x 24 inch long screen (not included) 6 inch flanged top inlet to screw feed 8 inch bottom center outlet for screened material 5 inch end […]

5 Hp PROCHEM AGITATOR DRIVE 240 rpm

Stock no. B-4289 5 Hp PROCHEM AGITATOR DRIVE 240 rpm Prochem Model PVTO-2-230 5 Hp, 1725 rpm, 208-230/460 v, 15-13.2/6.6 amps, 3 ph 240 rpm shaft speed. Stainless steel stub shaft Round flange mount on square steel plate (1) available

1.5 inch DEPA STAINLESS STEEL DIAPHRAGM PUMP

Stock no. P-3297 (5) 1.5 inch DEPA STAINLESS STEEL DIAPHRAGM PUMP Depa Pumpen model DL 40 SA CEE, made in Germany Air powered with 1.5 inch threaded fittings Available with or without tri-clamp adapter fittings (5) available

2.5 inch WAUKESHA STAINLESS STEEL 060 DISPLACEMENT PUMP

Stock no. P-3147 2.5 inch WAUKESHA STAINLESS STEEL DISPLACEMENT PUMP Model 060, Serial number 79552 SS 2.5 inch tri-clamp fittings We are able to set it up with a motor and gear reducer on either a stationary or portable platform. (1) available.

26.4 gallon/100 liter STAINLESS STEEL PORTABLE TANK CHAUDRINOX SS

Stock no. A-5546 (4) 26.4 gallon/100 Liter STAINLESS STEEL PORTABLE TANK Made in France by Chaudrinox SS Approximately 20 inch diameter x 16 inch straight side with dished bottom and top Has a 6 inch top center tri-clamp opening with (3) hose attachments one with a 1/2 inch dip tube. It does not have a […]

55 gallon STAINLESS STEEL JACKETED TANK

Stock no. E-4533 55 gallon STAINLESS STEEL JACKETED TANK 22.5 inch inside diameter x 34 inch with a side jacket 2.25 inch bottom center outlet To be cleaned and jacket pressure tested (1) available

4 inch WAUKESHA STAINLESS STEEL DISPLACEMENT PUMP 220

Stock no. P-3272 4 inch WAUKESHA STAINLESS STEEL DISPLACEMENT PUMP Model 220, serial number 19466 SS 4 inch tri-clamp fittings Came in with a Eaton hydraulic motor (will sell motor separately) We can change to an electric motor with gear reducer (1) available SALE PENDING

.33 HP 1 PH WATCHMAN B-STYLE PUMP CONDENSATE BOILER FEED TYPE

Stock no. P-3264 (2) .33 HP 1 PH WATCHMAN B-STYLE PUMP CONDENSATE BOILER FEED TYPE 1 inch threaded top port, 1 x 2.5 inch bottom rectangular port Cast Iron construction made by Hoffman 1/3 Hp, 3450 rpm, 115-208/230 v, 1 ph Designed for use on condensate and boiler feed units Precision balanced bronze impeller for […]

1 inch  POLY DIAPHRAGM PUMP

Stock no. P-3260 1 inch  POLY DIAPHRAGM PUMP Manufacturer unknown 1 inch threaded end fittings Bolted body. Air powered (1) available

01HD-6 SZEGVARI ATTRITOR SYSTEM UNION PROCESS

Stock no. C-2762 SZEGVARI ATTRITOR SYSTEM by UNION PROCESS Type 01HD, size 01HD-6, serial no. 940102 Powered by a Reeves 2 Hp, 1160 rpm, 230/460 v, XP Vari-drive Speed rating 345 to 1725 rpm output to multi-belt drive 6 Jacketed bowls, 4 with ss lids and 2 with plastic lids Extra linings, o-rings and misc. […]

2.5 x 1.5-6 GOULDS G & L STAINLESS STEEL CENTRIFUGAL PUMP

Stock no. P-3248 2.5 x 1.5-6 GOULDS G & L STAINLESS STEEL CENTRIFUGAL PUMP 4SHK6, 4SH2J57D2, date 5/3/16 Approx. 5 Hp (plate worn), 208-230/460 volt, 3 phase 2.5 inch x 1.5 inch flanged fittings, 5.62 inch diameter impeller Recently pulled off a Horizontal Tunnel Washer (1) available

1 inch GRACO STAINLESS STEEL DIAPHRAGM PUMP HUSKY 1040

Stock no. P-3230 1 inch GRACO STAINLESS STEEL DIAPHRAGM PUMP HUSKY 1040 Graco Husky 1040 series C04C, part number D74911 1 inch threaded inlet and outlet on one end air powered rated for 42-159 gpm, 120 psi max. Tested in good working condition (1) available

12 GALLON STAINLESS STEEL PRESSURE TANK 130 psi with outlet

Stock No. E-3679 12 GALLON STAINLESS STEEL PRESSURE TANK Mfg. Alloy Products Corp. 316 stainless steel rated for 130 psi @ 100 deg. F 3 x 4 inch top opening 1/4 and (3)3/8 inch top inlets. 3/4 inch side outlet 12 inch diameter x 24 inch with dished top and bottom On wheels (1) available

1.5 inch ECCENTRIC STAINLESS STEEL DISC PUMP C21 CVT

Stock no. P-2756 1.5 inch ECCENTRIC STAINLESS STEEL DISC PUMP Blackmer model C21 CVT, serial no. 527793,  year 2002 1.5 inch tri-clamp inlet and outlet 1 Hp, 1760 rpm, 90 v dc, 9.6 amp xp motor for hazardous locations Has speed control (to be tested) Last used for solvent based paper coatings. (1) available

30 inch SANITARY 316 STAINLESS STEEL CARTRIDGE FILTER CODE 7

Stock no. C-2756 30 inch SANITARY 316 STAINLESS STEEL CARTRIDGE FILTER CODE 7 Millipore catalog no. CES6944-1, eq. no. FLT-2711 zwa, year 2001 Rated for 150 psi @ 275 deg. F/135 deg. C Takes a single 30 inch long code 7 type twist in filter Has 1.5 inch bottom inlet and outlet, ends have been […]

1/2 inch POLY DIAPHRAGM PUMP

Stock no. P-3235 1/2 inch POLY DIAPHRAGM PUMP Manufacturer unknown. Has PE50 stamped on side 1/2 inch  inlet and outlet Air powered. Selling cleaned and tested. (1) available

1.5 Hp JWI VERTICAL DOWN MIXER JLI-150

Stock no. B-4252 1.5 Hp JWI VERTICAL DOWN MIXER Model JLI-150 1.5 Hp, 1725/1425 rpm input, 208-230/460 v, 3 ph, 60/50 Hz Approximately 300 rpm shaft speed 4-bolt mount, 12 inch square 4.5 inch diameter, 4-bolt flange for shaft mounting (1) available

500 gallon STAINLESS STEEL TANK with SWEEP MIXER and COIL

Stock no. A-5510 500 gallon STAINLESS STEEL TANK with SWEEP MIXER and COIL 56 inch x 4 ft. straight side and slight coned bottom Flat top with hinged lid and mixer Mixer is approximately 2 Hp, belt drive to a right angle gear box More info to follow on mixer, other options available Has a […]

14.5 gallon 316L STAINLESS STEEL PRESSURE TANK 115 psi

Stock no. E-4446 14.5 gallon 316L STAINLESS STEEL PRESSURE TANK 115 psi Alloy Products no. 101619-001, year 1999 Rated for 115 psi @ 100 deg. F 12 inch diameter x 30 inch with dished bottom and top 1.5 inch top tri-clamp fitting, (2) 1/4 inch and a 1/2 > 1/4 inch with a dip tube […]

5 gallon STAINLESS STEEL PRESSURE TANK 700 PSI

Stock no. E-1252 5 gallon STAINLESS STEEL PRESSURE TANK 700 PSI Mfg. SGL Piping Systems, serial no. 14953-B, year 1985 National Board no. 1041, rated for 700 psi @ 200 deg. F. ASME Sect. III, Div I, U stamped 12 inch diameter x 14 inch straight side with dished top and bottom 1 inch flanged […]

11 gallon STAINLESS STEEL TANK with AGITATOR

Stock no. A-5495 (15) 11 gallon STAINLESS STEEL TANK with AGITATOR 14 inch inside diameter x 17 inch deep with flat bottom, domed top Has a 6 inch top center port with a 4-blade agitator attached 1/4 an 1/2 inch top tube connection in stoppers in 1 inch holes. No bottom outlets Welded seems. (15) […]

13 gallon STAINLESS STEEL TANK with AGITATOR

Stock no. A-5492 (5) 13 gallon STAINLESS STEEL TANK with AGITATOR 14 inch inside diameter x 20 inch deep with flat bottom and flat fixed top 8 inch tri-clamp port with a 4-blade agitator attached 1/2 inch top tube connection in a stopper in a 7/8 inch hole Also a 1/4 inch fixed tube inlet. […]

WAUKESHA 024 SS DISPLACEMENT PUMP with HOPPER FEED 1.5 inch

Stock no. P-3209 1.5 inch WAUKESHA SS DISPLACEMENT PUMP with HOPPER FEED Waukesha Model 024, no. 378210 05 3 Hp, 1755 rpm, 230/460 v, 7.6/3.8 a with gear reducer with 125 rpm output 1.5 inch tri-clamp bottom outlet Hopper feed, 30 inch diameter > 7 inch x 21 inch tall + 6 inch extension to […]

1.5 Hp CHEMINEER VERTICAL DOWN FLANGE MOUNT MIXER 430 RPM

Stock no. B-4337 1.5 Hp CHEMINEER VERTICAL DOWN FLANGE MOUNT MIXER Model VLA-15, serial number 1-95408-6 1.5 Hp, 1750 rpm, 208-230/460 v, 3 ph motor, 430 rpm shaft speed Came in with 15.5 inch stainless steel faced 12-bolt flange, 19 inch od Has packing gland seal 1.25 inch diameter x 49.5 inch stainless steel shaft […]

50 Hp RIETZ VENTILATOREN RADIAL FAN MXE BLOWER

Stock no. G-3911 50 Hp RIETZ VENTILATOREN RADIAL FAN BLOWER Model MXE100-016030-00, serial number 266498, year 2010 37 Kw (50 Hp), 2955 rpm, 380-415 v, 65-61 amp, 50 Hz, 3 ph Flanged 14 inch side inlet and 10 inch outlet Mild steel construction O/a 56 inch x 42 inch x 48 inch tall. 1550 lbs […]

30 Hp AEROVENT STAINLESS STEEL TYPE S VANEAXIAL FAN BLOWER

Stock no. G-3908 30 Hp AEROVENT STAINLESS STEEL TYPE S VANEAXIAL FAN BLOWER Model 36B630-VSBD-1675-30, type VSBD, serial no. 12403429-1-1 30 Hp, 1770 rpm, 230/460 volt, 3 ph 36.5 inch inside diameter x 64 inch UNUSED, just in, catalog on file with additional details

3 gallon STAINLESS STEEL JACKETED TANK with MIXER

Stock no. E-4504 3 gallon STAINLESS STEEL JACKETED TANK with MIXER 8.75 inch inside diameter x 12 inch deep, flat bottom, clamped top (2) motor option, both 1/8 Hp, 90 v dc with speed controls Motors have different size pulleys for additional speed options (6) 1/4 inch top inlets with (3) dip tubes. 1/4 inch […]

2.5 x 1.5 inch SANITARY SS CENTRIFUGAL PUMP ALFA LAVAL

Stock no. P-3177 2.5 x 1.5 inch SANITARY SS CENTRIFUGAL PUMP Alfa Laval Model LKH10, description LKH10M150SS2EN18CA, no. 607081-07 5 Hp, 230/460 v, 3 ph Sanitary stainless steel, 2.5 x 1.5 inch tri-clamp connections Last used in a beverage recovery system, see A-5443 and P-3176 for other items (1) available

1 Hp LIGHTNIN VERTICAL DOWN FLANGE MOUNT MIXER

Stock no. B-4328 1 Hp LIGHTNIN VERTICAL DOWN FLANGE MOUNT MIXER Lightnin SPX Flow Model X5S100, no. 3293090, year 2017 1 Hp, 1760 rpm, 208-230/460 v, 3 ph gear reduced Has a place for a seal, but no seal with it 8.5 inch stainless steel face on 11 inch od flange Stainless steel shaft mount […]

4 ft. STAINLESS STEEL LAB HOOD

Stock no. G-3905 4 ft. STAINLESS STEEL LAB HOOD Unsure of manufacturer. Catalog no. 4302PE/SS/SP/RECPT, no. 10248-1 Has a National Air Filter Certificate dated 2015 (2)White fluorescent lights and (1) yellow light with diffuser grids Inch water column gauge for pressure, blower, 115 volt, 1 phase, 60 Hz, 15 amps Top front filter exhausts into […]

2 cu. ft. KELLY DUPLEX PLOW BLENDER CARBON STEEL

Stock no. B-4324 2 cu. ft. KELLY DUPLEX PLOW BLENDER CARBON STEEL Made by The Duplex Mill and Manufacturing Co. Model 191, serial no. 62076 1 Hp, 3 phase motor to 43.35 to 1 ratio gear box, 1700 rpm in, 39 rpm out Control box, Start, Stop, and Reset Has (2) plow type rotating blades. […]

2730 Btu R025 HASKRIS WATER COOLED CHILLER 115 V

Stock no. G-3897 2730 Btu per Hour HASKRIS WATER COOLED CHILLER Model R025, serial number HB20622 R134A refrigerant, 2 lbs. 10 oz charge 4.9 RLA, 25 LRA, 1 Ph compressor 1/3 Hp pump, 5.6 FLA, 115 v, 1 ph Digital controls, water level gauge Return and supply in and out, water in and out fittings […]

1.17 Hp LIGHTNIN CLAMP MOUNT MIXER XJ-117

Stock no. B-4311 (2) 1.17 Hp LIGHTNIN CLAMP MOUNT MIXER Model XJ-117 with 1.17 Hp, 230/460 v, 4.2-2.1 amp, 3 ph Gear reduced, stainless steel base and contacts Can include clamp or bolt on mount Stainless steel shafts made to order. (2) available

1/2 Hp CHEMINEER VERTICAL DOWN MIXER

Stock no. B-4300 1/2 Hp CHEMINEER VERTICAL DOWN MIXER Serial number 525557-1 1/2 Hp, 1750 rpm, 230/460 v, 3 ph, Inverter Duty motor Gear reduced, 4.71-1 ratio, 371 rpm shaft speed We make up stainless steel shafts to order. (1) available

1.5 inch CAST IRON GEAR PUMP HAIGHT 24UR

Stock no. P-3140 1.5 inch CAST IRON GEAR PUMP No mfg. plate but compares to a Haight model 24UR with relief valve Assembly by Fischer Pump and Valve Co, no. 6974 1.5 inch NPT side inlet and side outlet 1/2 Hp variable speed Eurodrive motor, 230/460 v, 3 ph Gear reducer with 20 to 97 […]

2 Hp PROCHEM AGITATOR DRIVE 226 rpm 20VM2S

Stock no. B-4293 2 Hp PROCHEM AGITATOR DRIVE 226 rpm Model 20VM2S, made by Chemineer serial no. 517346-1 2 Hp, 1735 rpm, 230/460 v, 5.8/2.9 amps, 3 ph 226 rpm shaft speed. Stainless steel stub shaft Round flange mount on square steel plate

5 Hp PROCHEM AGITATOR DRIVE 249 rpm

Stock no. B-4290 5 Hp PROCHEM AGITATOR DRIVE 249 rpm Prochem Model PVTO-3-230 5 Hp, 1160 rpm, 230/460 v, 15.8/7.9 amps, 3 ph 249 rpm shaft speed. Stainless steel stub shaft Round flange mount on square steel plate (1) available

4.5 gallon 316L STAINLESS STEEL PRESSURE TANK FV 130 psi

Stock no. E-4457 4.5 gallon 316L STAINLESS STEEL PRESSURE TANK FV 130 psi Alloy Products year 2000 rated for Full vacuum/130 psi @ 100 deg. F 9 inch diameter x 17 inch straight side with dished top and bottom Tri-clamp top inlets = (3) 1/4 inch and a 1/2 inch with dip tube No bottom […]

3/4 Hp MIKRO PULVERIZER TYPE CF GRINDER

Stock no. C-2737 3/4 Hp MIKRO PULVERIZER TYPE CF GRINDER No. 8513, Type CF by Pulverizing Machinery Bronze lined housing, rest of machine is carbon steel 3/4 Hp, 3450 rpm, 110/220 volt, single phase Belt drive with a manual screw feeder (1) available

2 Hp EURODRIVE FLANGE MOUNT GEAR REDUCER 33 rpm

Stock no. B-4277 2 Hp EURODRIVE FLANGE MOUNT GEAR REDUCER 33 rpm 2 Hp, 1720 rpm, 230/460 volt, 6.2/3.1 amps 52.82-1 ratio, 33 rpm output to 2 inch diameter stub shaft 4 bolt flange mount, 9 inch id x 11.5 inch outside diameter. Bolt holes are 10 inch ctr>ctr across (1) available

3/4 Hp EURODRIVE FLANGE MOUNT GEAR REDUCER 40 rpm

Stock no. B-4278 (3) 3/4 Hp EURODRIVE FLANGE MOUNT GEAR REDUCER 40 rpm 3/4 Hp, 1700 rpm, 230/460 volt, 2.90/1.45 amps 42.87-1 ratio, 40 rpm output to 1.25 inch diameter stub shaft 4 bolt flange mount POSSIBLY UNUSED (3) available

30 Hp CHEMINEER 6HTA-30 RIGHT ANGLE DRIVE 68 rpm

Stock no. B-4214 30 Hp CHEMINEER Model 6HTA-30 RIGHT ANGLE DRIVE Serial no. 562255-1 68 rpm with 1800 rpm input, rated for 30 Hp Sell with or without motor setup Shafts and blades made up to order (1) available

1/2 Hp CLAMP MOUNT MIXER 230/460 V JWI

Stock no. B-4207 1/2 Hp CLAMP MOUNT MIXER JWI model JL50, gear reduced 1/2 Hp, 1725 rpm, 230/460 volt, 3 ph Approximately 350 rpm output Takes bolt on shaft which we can make to order (1) available

11 gallon 42 liter 316 L Stainless Steel BIO Reactor FV 46.5 psi

Stock no. E-4413 42 liter 316 L Stainless Steel BIO Reactor FV 46.5 psi MBR BIO Reactor AG Switzerland type Labor Pilot 42 L, machine no. 751 Certified by Ludwig Edel Gmbh and Co. no. 90172/4, year 1992 316L stainless steel shell and 304 stainless steel jacket National Board 100, U stamped. U-1 report on […]

260 gallon CONE BOTTOM POLY TANK OPEN TOP

Stock no. A-4795 260 gallon CONE BOTTOM POLY TANK OPEN TOP 40 inch diameter x 48 inch straight side with cone bottom 4 inch bottom center outlet with no fittings. (3) 1.25 inch id side fittings, 35.25, 49, and 58.25 inch from ground Has slight crack under the top rim on one side but should […]

1.5 Hp LIGHTNIN VERTICAL DOWN MIXER FLANGE MOUNT 150 rpm

Stock no. B-4189 1.5 Hp LIGHTNIN VERTICAL DOWN MIXER FLANGE MOUNT Model 1S110, no. 102058, year 2002, made in China Rated for 1.27 Kw @ 440 volt, 60 Hz (1.5 Hp), 840 rpm 1.1 Kw 220/380 volt, 50 Hz, 700 rpm 150 rpm shaft output speed listed on plate Stainless steel contacts with 14 inch […]

LIGHTNIN CLAMP MOUNT LAB MIXER STIRRER

Stock no. B-4183 LIGHTNIN CLAMP MOUNT LAB MIXER STIRRER 1/15 Hp, 115 volt, 1600 rpm. Model S1U05T Stainless steel shaft, 18 inch to chuck, 22 inch to bottom of mixer With 3.5 inch A310 type blade Optional stainless steel stand available at additional charge (1) available

3 inch WAUKESHA STAINLESS STEEL DISPLACEMENT PUMP 201U

Stock no. P-2972 3 inch WAUKESHA STAINLESS STEEL DISPLACEMENT PUMP 201U Waukesha model 201U, no. 0000245826 3 inch threaded outlet, 3 x 9 inch rectangular inlet Will sell with or without a motor setup (1) available Possibly sold.

15 GALLON STAINLESS STEEL PRESSURE TANK with outlet 130 psi

Stock no. E-3352 (2) 15 GALLON STAINLESS STEEL PRESSURE TANK Mfg. Alloy Products Corp. 316 stainless steel rated for 130 psi @ 100 deg. F 3 x 4 inch top opening with lid 1/4 and (3)3/8 inch top inlets. 1.5 and 3/4 inch side outlet 12 inch diameter x 32 inch with dished top and […]

3 Hp STAINLESS STEEL SWEEP AGITATOR DRIVE

Stock no. B-4174 3 Hp STAINLESS STEEL SWEEP AGITATOR DRIVE Manufactured by Shar, more info to follow 3 Hp, 1170 rpm, 208-230/460 volt, 3 ph Gear reduced Came off a 250 gallon tank rated for 30 psi, 40 inch id x 48 inch straight side No longer with tank top in picture (1) available SALE […]

20 gallon 316 STAINLESS STEEL JACKETED REACTOR 65 psi

Stock no. E-4384 20 gallon 316 STAINLESS STEEL JACKETED REACTOR Pfaudler no. E53630, rated for 65 psi 20 inch diameter x 16 inch with dished bottom and dished clamped top 2 inch top center inlet plus assorted other top inlets Has a 1.5 inch bottom center outlet (1) available

1 Hp LIGHTNIN FLANGE MOUNT MIXER XP N33G-100

Stock no. B-4163 1 Hp LIGHTNIN FLANGE MOUNT MIXER XP Model N33G-100, no. 7315427 1 Hp, 1745 rpm, 230/460 v, 3 ph, for hazardous locations Gear reduced, 350 rpm shaft speed 1.5 inch diameter shaft, mechanical seal with a 10 inch od 8-bolt flange (1) available

.65 Hp LIGHTNIN FLANGE MOUNT MIXER with MECHANICAL SEAL

Stock no. B-4164 .65 Hp LIGHTNIN FLANGE MOUNT MIXER with MECHANICAL SEAL Model XJDS-65, no. 88/345122 .65 Hp, 1140/960 rpm 208-230/460 v, 60/50 hz, 3 ph XP for hazardous locations 1.25 inch diameter shaft, approx. 288 rpm output 9 inch stainless flange face, 11 inch outside diameter (1) available

3 inch ALUMINUM DIAPHRAGM PUMP VERSA-MATIC

Stock no. P-3058 (2) 3 inch VERSA-MATIC ALUMINUM DIAPHRAGM PUMP 3 inch inlet and outlet Air powered. Refurbished and tested Similar to Wilden Pump, some parts are interchangeable (2) available

5 Hp VERTICAL DOWN MIXER EKATO

Stock no. B-4147 5 Hp VERTICAL DOWN MIXER by EKATO Model EM2040, no. 66311-10, year 2004 Originally with a 5 Hp motor shown in picture (to be replaced) 1750 rpm, 3 ph, 60 hz, direct drive Has dust seal, rated for 14.5 psi @ 212 deg. F Takes a 1.5 inch diameter shaft. 4-bolt flange […]

3 Hp SIDE ENTERING AGITATOR MIX PRO

Stock no. B-4148 3 Hp SIDE ENTERING AGITATOR MIX PRO Model 12VSM rated for 345 rpm with 1800 rpm input 1.25 inch diameter x 15 inch stainless steel shaft 17 inch prop Sell with or without motor setup Looks unused! (1) available SALE PENDING

.43 Hp LIGHTNIN CLAMP MOUNT MIXER 3 ph

Stock no. B-4141 (2) .43 Hp LIGHTNIN CLAMP MOUNT MIXER Model XJ43 .43 Hp, 1725 rpm, 208-230/460 v, 3ph Has custom quick disconnect for shaft Will furnish with clamp mount or swivel bolt mount (2) available

4 x 13 inch STAINLESS STEEL BASKET FILTER STRAINER

Stock no. C-2711 4 x 13 inch STAINLESS STEEL BASKET FILTER STRAINER Manufacturer SSI Equipment INC. Serial no. 96-4676. model 150 BFSSBWOB. tag no. D-1279. year 1997 5 1/2 inch diameter X 16 inch tall, dished cover and dished bottom stainless steel. 2 inch side in and out. 3/4 inch out in lid and bottom drain […]

1.5 inch STERLING LIQUID RING VACUUM PUMP

Stock no P-3038 1.5 inch STERLING LIQUID RING VACUUM PUMP Model 909114, serial no. C05-534000-03 1.5 inch inlet and outlet Cast iron construction Will sell pump alone or setup with a motor on a platform (1) available

1/2 Hp CHEMINEER CLAMP MOUNT MIXER 1 ph XP

Stock no. B-4134 (2) 1/2 Hp CHEMINEER CLAMP MOUNT MIXER model 3JTC-0.50 1/2 Hp, 1750 rpm, 115/230 volt, 3 ph, XP Direct drive. Takes a 1 inch diameter shaft included with a single prop (2) available

40 gallon STAINLESS STEEL JACKETED TILT KETTLE

Stock no. E-4352 40 gallon STAINLESS STEEL JACKETED TILT KETTLE Sanitary stainless steel from food service No mfg. id plate, assume low pressure jacket 26 inch diameter x 22 inch deep Manual crank tilt for dumping, no outlet Mounted on 16 inch diameter x 11 inch tall pedestal. O/a 36 inch diameter x 40 inch […]

7 x 28 inch STAINLESS STEEL BASKET FILTER 2 inch fittings

Stock no. C-2317 (2) 7 x 28 inch STAINLESS STEEL BASKET FILTER 2 inch fittings Mechanical Mfg. Co. no. 24019 7 x 28 inch stainless steel filter basket. 9 inch diameter x 33 inch housing (1) 3/4 and (3) 1/4 inch NPT fittings, 2 inch 4-bolt flanged side in & out Legs/stand included rated to […]

1.5 Hp CHEMINEER VERTICAL DOWN MIXER 3BTNS-15 with motor

Stock no. B-4093 1.5 Hp CHEMINEER VERTICAL DOWN MIXER with motor UNUSED Model 3BTNS-15, no. 1-97411-4 Includes motor not pictured, 1.5 Hp, 1780 rpm, 230/460 v, 3ph Gear reduced with Hub City gear box model 254 5/1, style 0010 UNUSED! In crate with original packing slip (1) available

6 gallon ELECTRIC KETTLE JACKETED TANK SWEEP AGITATOR

Stock no. E-4320 (4) 6 gallon ELECTRIC KETTLE JACKETED TANK SWEEP AGITATOR 12.5 inch inside diameter x 11 inch with dish bottom, 2 piece lid Polished stainless steel. Has a label SSS 40 Watt half sweep agitator, 90 Watt for center shaft to bottom metering out 200-240 V., 3 ph gear reduced induction motors on […]

TUTHILL 16-SS STAINLESS STEEL DISPLACEMENT PUMP 1.5 inch

Stock no. P-2838 1.5  inch STAINLESS STEEL DISPLACEMENT PUMP TUTHILL TUTHILL (CHICAGO). Serial no. 04-0309-10, model 16-s.s, 25526 Stainless steel 1.5 inch threaded in and out 1.5 hp, 1165 rpm, 3 ph,230/460 volt, 5.7-2.8 amp Compares in size to a Waukesha model 15, with Bat wing type rotors (1) available

2 gallon GROEN ELECTRIC TILT KETTLE 8 quart

Stock no. E-3816 2 gallon GROEN ELECTRIC TILT KETTLE MODEL tdb/ 5-8, 1970, National Board no. 54655 Rated for 50 psi @ 300 deg F max. 8 quart capacity, 2 gallons stainless steel 10″ diameter x 8″ deep , dished bottom, open top 208 volt. 1 ph, kw 3.6, SUBJECT TO TESTING **

30 gallon STAINLESS STEEL REACTOR JACKETED TANK

Stock no. E-4306 30 gallon STAINLESS STEEL REACTOR JACKETED TANK 16 inch diameter x 36 inch w/dished bottom clamped dished top, 21 inch outside diameter has plate with these numbers only 6701-18 4-4100-127 jacketed and insulated, no rating listed tri-clamp top = 4 inch, 2 inch, (2) 2.5 inch, and (4) 1 inch. Approx. 2 […]

3 inch WAUKESHA STAINLESS STEEL DISPLACEMENT PUMP 130

Stock no. P-2969 3 inch WAUKESHA STAINLESS STEEL DISPLACEMENT PUMP Model 130, serial no. 216357 98 3 inch I line type tri-clamp fittings Will sell with or without motor and gear reducer setup Several similar available

1 inch TRI-HOMO STAINLESS STEEL COLLOID MILL 5 Hp

Stock no. C-2681 1 inch TRI-HOMO STAINLESS STEEL COLLOID MILL Model 4LA, no. 042277 5 Hp, 3485 rpm, 230/460 v, 3ph 1 inch tri-clamp in and out on 6 inch diameter head to be assembled Rated for 15-50 gph low viscosity, 10-30 gph heavy with gravity flow 50-600 gph medium viscosity pressurized to 50 psi […]

1.5 inch CREPACO STAINLESS STEEL DISPLACEMENT PUMP R3R

Stock no. P-2981 1.5″  CREPACO STAINLESS STEEL DISPLACEMENT PUMP R3R Creamery Package Company Model R3R, no. B-6599, with Resilient type rotors 1.5″ threaded dairy type fittings Sell pump alone or with motor setup (1) available SALE PENDING

1.5 inch SIZE 3 CREPACO STAINLESS STEEL DISPLACEMENT PUMP

Stock no. P-2980 1.5″  SIZE 3 CREPACO STAINLESS STEEL DISPLACEMENT PUMP Creamery Package Company No. 3R-4919. with Resilient type rotors 1.5″ threaded dairy type fittings Sell pump alone or with motor setup (1) available SALE PENDING  

200 gallon MUELLER TANK with INTERNAL PLATE COIL

Stock no. E-4305 200 gallon MUELLER  TANK with INTERNAL PLATE COIL Model RHP200, no. 105738 .23 cu. ft. coil volume, 113 psi max, originally R-12 medium 46 inch inside diameter x 33  > 34.5 inch slant bottom 1.5 inch tri-clamp side outlet on low side, 1.5 inch threaded side outlet opposite side 31 inch diameter […]

420 gallon FIBERGLASS TANK SUMP

Stock no. A-4667 420 gallon FIBERGLASS TANK SUMP Manufactured by Xerxes, SO. 51190, PO 112704, year 1998 Fiberglass Dion 9300 4′ diameter x 54″ with flat bottom and closed top Rated to 120 deg. F. Sump tank with internal baffles Has (3) 18″ top flanged fittings, a 22″ side flanged fitting Has 2″ and 3″ […]

275 gallon FIBERGLASS TANK FLAT TOP AND BOTTOM

Stock no. A-1619 275 gallon FIBERGLASS TANK 3 ft  diameter x 62 inch with flat bottom and flat bolted lid 5.5 inch side outlet, 3 inch side inlet 1, 3, and 4 inch top inlets Mounted on legs (1) available

1.25 inch GRUNDFOS MULTI STAGE STAINLESS STEEL CENTRIFUGAL PUMP

Stock no. P-2946 1.25 inch GRUNDFOS MULTI STAGE STAINLESS STEEL CENTRIFUGAL PUMP Type CRN-3-5 A-FGJ-G-E-HQQE Model A96083904-P1092596 3/4 Hp, 3450 rpm, 115/230 volt, 1 ph, 60 hz Rated for 116.5 to 156.5 ft. head and to 15.41 gpm 1.25 inch flanged in and out Used for Reverse Osmosis water circulation (1) available

18.5 x 12 inch POLISHED STAINLESS STEEL CONE TANK

Stock no. A-5195 18.5 x 12 inch POLISHED STAINLESS STEEL CONE TANK 18.5 inch inside diameter x 12 inch with cloth type 6 inch valve for powders NO LONGER WITH STAND Possibly 316 stainless steel (need to test) (1) available Priced cone only

10 gallon HASTELLOY PRESSURE TANK

Stock no. E-3868 (2) 10 gallon HASTELLOY PRESSURE TANK Manufacturer Alloy Products Corp. Serial no. 600411-001, year 1996 Dimensions 11″ diameter x 25″ dish bottom + top Hastelloy C construction Rated for 100 psi @ 100 deg F, – 20 deg F @ 100 psi, F/V Inlets/outlets 4″ x 6″ oval top center port, (2) .5″ […]

2 inch WAUKESHA STAINLESS STEEL DISPLACEMENT PUMP 040

Stock no. P-2926 2 inch WAUKESHA STAINLESS STEEL DISPLACEMENT PUMP Model 040-08, no. 1000002111381 Has 1.75 inch id inlet and outlet with 3 inch I line sanitary fittings Will sell with or without motor and gear reducer setup (1) available

340 gallon CONE BOTTOM POLY TANK CLOSED TOP

Stock no. A-5137 340 gallon CONE BOTTOM POLY TANK with closed top Mfg. by Ecar Inc. 52 inch diameter x 27 inch straight side, 20 inch cone and dished top 1.5 inch bottom center outlet, 18 inch top manway several top inlets and (1) 3/4 inch side inlet It currently does not have a stand […]

6.5 gallon HEAVY GAUGE STAINLESS STEEL TANK POT

Stock no. A-3390 6.5 gallon HEAVY GAUGE STAINLESS STEEL TANK POT Has a smooth finish and will clean up well. 14.5″ inside diameter x 9.5″ deep Carbon steel outer base, 2 handles and trunions (2) available, one with a side outlet and the other no outlet

2.5 gallon STAINLESS STEEL TANK POLISHED FINISH BOTTOM GLASS

Stock no. A-5136 2.5 gallon STAINLESS STEEL TANK POLISHED FINISH UNUSED DCI Inc, serial no. JS4158C, year 2008 8 inch diameter x 19 inch w/flat top & clamped flat bottom Sanitary polished stainless vertical, UNUSED **** Rated for 0 psi @ 100 deg. F, to -20 deg. F Top= 1.5 inch and (3) 2 inch tri-clamp, (2) […]

3 inch WAUKESHA 130 STAINLESS STEEL DISPLACEMENT PUMP

Stock no. P-2900 3″ WAUKESHA SANITARY STAINLESS STEEL DISPLACEMENT PUMP Model 130, no. 24602831-10 With 3″ tri-clamp in and out Will sell with or without motor and gear reducer setup Other similar pumps available

2 Hp LIGHTNIN VERTICAL DOWN MIXER XP

Stock no B-4017 2 Hp LIGHTNIN VERTICAL DOWN MIXER XP Model NLDG200, no. 700317 2 Hp, 2 speed motor, 1765 /880 rpm, 480 volt, 3 ph XP Gear reduced, 350 rpm/175 rpm shaft speed Flange mount for shaft. Optional angle mount attached (1) available, other similar mixers available

1/3 Hp LIGHTNIN VEKTOR CLAMP MOUNT MIXER 3 ph

Stock no. B-3999 1/3 Hp LIGHTNIN VEKTOR CLAMP MOUNT MIXER No. 94B87609-10 .33 Hp, 1750 rpm, 208-230/460 volt, 3ph Gear reduced. Takes a 1″ diameter shaft. Stainless steel shaft and prop sized to order. (1) available

30 inch x 7 STAINLESS STEEL MULTI CARTRIDGE FILTER

Stock no. C-2659 (2) 30 inch x 7 STAINLESS STEEL MULTI CARTRIDGE FILTER No mfg. tag. Takes (7) 30 inch slip in style cartridges 9 inch diameter x 33 inch with dished bottom & clamped top Polished stainless steel exterior with 316 stainless steel flanges Inside is coated but has peeled in a couple of […]

100 gallon STAINLESS STEEL JACKETED TANK

Stock no. E-4233 (2) 100 gallon STAINLESS STEEL JACKETED TANK 24 inch diameter x 48 inch with cone bottom, open top 1 inch bottom center outlet and side outlet, 2 inch side inlet 3/4 inch thermal well. 1/2 side jacket with 1 inch jacket inlet and outlet Has gussets that we can add legs to. […]

1 Hp LIGHTNIN CLAMP MOUNT MIXER

Stock no. B-4035 1 Hp LIGHTNIN CLAMP MOUNT MIXER Model ND3, no. 553640 1 Hp, 1760 rpm, 208-230/460 v, 3ph Gear reduced, 350 rpm shaft Flange for shaft mount. Sell with or without shaft and prop (1) available

VIKING S2S STAINLESS STEEL DISPLACEMENT PUMP 1.5 inch

Stock no. P-2834 1.5 inch VIKING STAINLESS STEEL DISPLACEMENT PUMP Model S2S rated for 6 gpm, 150 psi Has 1.5 inch tri-clamp in and out. Originally with 2 Hp, 1725 rpm, 208-230/460 v, 3ph Motor to be replaced or sell without (1) available

350 gallon 304 STAINLESS STEEL JACKETED TANK

Stock no. E-4174 350 gallon 304 STAINLESS STEEL JACKETED TANK 41.5 inch inside diameter x 60 inch with dished bottom, open top Has 2 sets of brackets for baffles, approx. 2 inch bottom center outlet Side probe inlet and 1 inch side outlet Has carbon steel jacket, side and bottom inlets and outlets (1) available

2 inch SPECO STAINLESS STEEL INLINE MIXER

Stock no. B-3992 2 inch SPECO STAINLESS STEEL INLINE MIXER Model 2TSPL, s/n 79-10635 o/a 24 inch x 46 inch x 46 inch including cart w/(4)wheels. 2 inch x 2 inch in and out w/ reducer flange to 1 inch 3 hp, 1735 rpm input, variable speed 420-4200 rpm output 230/460v, 3ph, 60hz. (1) available

8 gallon POLISHED STAINLESS STEEL TANK DISPENSER

Stock no. G-2809 8 gallon POLISHED STAINLESS STEEL TANK DISPENSER SETUP 10 inch diameter x 20 inch  with dished bottom, clamped top No manufacturer plate but marked model 17001-2-10, 28 inch x 1.5 inch tri. Serial no. 00-8171-1A 1.5 inch tri-clamp bottom center outlet, 1.5 inch side out, 2 inch side in Assorted top fittings […]

10 gallon STAINLESS STEEL TANK

Stock no. A-3331 10 gallon STAINLESS STEEL TANK 11.5″ diameter x 22″ with flat bottom and open top 2″ side inlet, 1.25″ side outlet (2) handles (1) available

3000 Gallon HORIZONTAL STAINLESS STEEL FLAMMABLE STORAGE

Stock no. A-4910(2) 3000 Gallon DUAL COMPARTMENT STAINLESS STEEL SOLVENT TANK Stainless steel with concrete outer shell designed for flammable liquid storage. 114 inch wide x 154 inch long x 10 ft. 6 inch tall including 2 support cradles. Approx. 45,000 lbs each. Top fittings have been removed. (2) available YOU CAN HAVE THESE FOR […]

.25 inch AMERICAN LEWA INC. METERING PUMP

Stock no. P-2031 .25 inch AMERICAN LEWA INC. METERING PUMP Serial no. 228399-010.004, 1991, model FC 08 Stainless steel, (4) .25 inch in and out 1/2 hp, 1725 rpm, 3 ph, 230/460, 1.5 amp (2) available

1/2 Hp SHAR VERTICAL DOWN MIXER 85 RPM

Stock no. B-1617 1/2 Hp SHAR VERTICAL DOWN MIXER Serial no. 12103794 1/2 Hp, 1750 rpm, 3 ph motor Gear reduced to 85 rpm shaft speed Currently mounted on tank lid (1) available

5 gallon ELECTRICALLY HEATED GROEN TILT KETTLE

Stock no. E-3921 (2) 5 gallon ELECTRICALLY HEATED GROEN TILT KETTLE Model TDB-7-20 rated for 50 psi @ 300 deg. F. Year 1990 440 volt, 3 phase 14 inch inside diameter x 12 inch deep, 1 inch jacket fittings Subject to testing (2) available

950 gallon STAINLESS STEEL TANK ATMOSPHERIC

Stock no. A-5058 950 gallon STAINLESS STEEL TANK Mfg. Letsch Corp. serial no. 2194 rated for atmospheric @ 100 deg. F 70 inch diameter x 56 inch plus dished bottom and closed dished top Has a 6 inch bottom center outlet With 3 inch side inlet, (2) 2 inch and (2) 6 inch top inlets […]

530 gallon 304 STAINLESS STEEL TANK

Stock no. A-5048 530 gallon 304 STAINLESS STEEL TANK UTENSCO no. 9405-1, 1978 52 inch diameter x 5 ft with slant bottom, closed top 16 inch, 2 inch, and 1 inch top inlets, 2 inch side outlet Industrial use. Has a dent on one side. We can try to take out most of the dent. […]

2.25 x 2.25 ALL STAINLESS STEEL SUMP PUMP

Stock no. P-2812 2.25 x 2.25 STAINLESS STEEL SUMP PUMP Has threaded 2.25″ in and out, all stainless steel construction 3-wire single phase, most likely 115 v No identifying marks From a food plant, subject to testing (1) available

1/4 Hp VERTICAL DOWN GEAR REDUCED MIXER

Stock no. B-3908 (2) 1/4 Hp VERTICAL DOWN GEAR REDUCED MIXER UET Excel Ram 20, yr 2005 1/4 Hp, 1750 rpm, 208-230/460v, 3ph 350 rpm shaft speed, 4 bolt mount (2) available  

2 Hp BRAWN VERTICAL DOWN MIXER GEAR REDUCED

Stock no. B-3871 (2) 2 Hp BRAWN VERTICAL DOWN MIXER GEAR REDUCED Model BGMF200SP 2 Hp, 1740 rpm, 230/460 v, 3ph, motor (motor to be replaced) Gear reduced (1) is currently mounted on a 22 inch stainless steel lid for a tote tank/IBC or drum (2) available

1 Hp CHEMINEER CLAMP MOUNT MIXER 336 rpm

Stock no. B-3946 1 Hp CHEMINEER CLAMP MOUNT MIXER Model X Press Portable, 1 Hp, 1750 rpm 230/460v, 3ph 5.21 gear ratio , 336 rpm max shaft speed Comes with stainless steel shaft and prop (1) available

1 Hp AIR MIXER with SPEED CONTROL and TRI-POD MOUNT

Stock no. B-3942 1 Hp AIR MIXER with SPEED CONTROL and TRI-POD MOUNT Approx. 1 Hp by physical size of mixer, looks like a Gast mixer Automatic and manual speed controls with forward and reverse Adjustable tri-pod mount for top of tank With regulator and filter (1) available

3 inch APV DW5 SANITARY STAINLESS STEEL DISPLACEMENT PUMP

Stock no. P-2788 3 inch APV DW5 SANITARY STAINLESS STEEL DISPLACEMENT PUMP Type DW5/093/025, no. 10002079, 27128028 3 inch tri-clamp in and out Rated to 24.6 gallons per 100 rpm, to 362 psi Aseptic positive displacement bi-lobe pump (1) available

1/2 Ton BUDGIT ELECTRIC CHAIN FALL HOIST

Stock no. G-3548 1/2 Ton BUDGIT ELECTRIC CHAIN FALL HOIST No. 3149166, 1,000 lb. capacity 1/2 Hp, 1725 rpm, 230/460 volt, 3 phase Chain speed rated for 16 feet per minute (1) available

1/3 Hp LIGHTNIN VERTICAL DOWN MIXER 115 VOLT

Stock no. B-3922 (2) Lightnin model NLDG-33 gear reduced vertical down mixer 1/3 Hp, 1725 rpm > 350 rpm shaft speed, 115v, 1 ph 4-bolt mount. Takes 5/8″ diameter shaft Please note that we test, clean, and paint our mixers before shipping. (2) available

3 Hp PRO QUIP RIGHT ANGLE DRIVE 10:1 RATIO

Stock no. B-3771 Pro Quip 3 Hp right angle drive mixer Model 300 JLX10P, no. 16007 Rated for 3 Hp, 10-1 ratio Takes a 1.5 inch diameter shaft Sell with or without a motor (1) available

1/2 Hp NEPTUNE CLAMP MOUNT MIXER

Stock no. B-3768 1/2 Hp NEPTUNE CLAMP MOUNT MIXER Neptune 1/2 Hp clamp mount mixer model D-1.7, no. 117713 Direct drive, with 90 v dc motor. Requires 115 v speed control not included Will include a clamp for mounting (1) available

5 Hp STAINLESS STEEL INLINE MIXER EMULSIFIER ROSS

Stock no. B-3779 5 Hp STAINLESS STEEL INLINE MIXER EMULSIFIER ROSS Ross series 300 stainless steel inline mixer with 3.5 inch diameter rotor No plate, but compares with a model 305 Ross inline mixer emulsifier Tagged MCC 23-5 3-CD, 127-305-48 Blender Coating Prep 5 Hp, 3450 rpm, 460 v, 3 ph, xp 18 inch diameter […]

1.5 inch PLASTIC COMPOSITE CENTRIFUGAL PUMP

Stock no. P-2719 Iwaki America plastic composite centrifugal pump CMD 187, no. 0510060620 1.5″ x 1.75″ id in and out 3 Hp, 3450 rpm, 208-230/460v, 3ph Rated for 10 gpm, 70 ft. hd. Does have a broken base, but otherwise looks great. (1) available

4 Kw HOT WATER HEATER 480 volt

Stock no. G-3530 4 Kw HOT WATER HEATER 480 volt Ogden 4 Kw hot water heater, circulating type Catalog no.  K8A-18-0030-M2 480 v, 3 ph 2.5″ side inlet and outlet, 1″ drain (1) available

125 gallon STAINLESS STEEL TANK WITH EXTERNAL COILS

Stock no. E-4021 (3) 125 gallon STAINLESS STEEL TANK WITH EXTERNAL COILS 125 gallon stainless steel cone bottom tank with external coil wrap 30 inch diameter x 36 inch straight side with 6 inch cone bottom, flat top 3 inch bottom center outlet, 1 inch diameter coils, hinged lid (not shown) Coils are not part […]

5.5 x 13 inch ROSEDALE STAINLESS STEEL BASKET BAG FILTER

Stock no. C-2513 5.5 x 13 inch ROSEDALE STAINLESS STEEL BASKET BAG FILTER Model/serial no. C022423, mdl 6-12-1p-150-d-s-b-n-b, 6/5/89 Manufacturer ROSEDALE Takes a 5.5 x 13 inch basket, housing 5 5/8 x 17.5 inch Stainless steel rated for 150 psi, single pass 1.25 inch threaded side in and bottom out Adjustable legs. MISSING BASKET***

7 inch x 6 inch STAINLESS STEEL CONE BLEND TANK

Stock no. A-4780 7 inch x 6 inch STAINLESS STEEL CONE BLEND TANK Labeled Etikettenfeld 7 inch diameter x 6  inch with clamp lid High Polished stainless steel, Pharma grade No outlet (1) available

4 gpm VAPONICS REVERSE OSMOSIS FILTER

Stock no. C-2523 4 gpm VAPONICS REVERSE OSMOSIS FILTER Model/serial no. 91-a23144A, model 19cvf-hr(pa)6000/ecn-sp Manufacturer Vaponics Div. Of Osmonics stainless STEEL contactS final pressure 235 psi, primary pressure 140 psi (4) 4 inch x 4 ft. ss filter housings, auto /manual controls RO divert pane, level control panel SB 1816x-12200-n Tonkaflo pump 115v control, 208-230/460 […]

FLOWTECH 1 inch SANITARY SS DISPLACEMENT PUMP UNIBLOC 300

Stock no. P-2572 1 inch SANITARY STAINLESS STEEL DISPLACEMENT PUMP Flowtech Unibloc Size 300,  serial no. 0098 Sanitary stainless steel Rated for 2.8 gal/per/rev, 28 gpm max. 1 inch id tri-clamp in & out Includes base to be mounted on, cart is an option Priced with motor setup but not exactly as pictured

3.5 liter STAINLESS STEEL PRESSURE TANK

Stock no. E-3856 (2) 3.5 liter STAINLESS STEEL PRESSURE TANK Manufacturer ACME IND.EQUIP./THE HODGE GROUP 4.5 inch inside diameter x 11 inch with dished bottom, clamped flat top Construction/configuration stainless steel vertical Full Vacuum/110 psi @ 325 deg. F. Year 1995 No bottom outlet! With agitator. NO MOTORS INCLUDED!! (2) AVAILABLE

VIKING LC20S STAINLESS STEEL DISPLACEMENT PUMP 1 inch

Stock no. P-2717 1 inch VIKING STAINLESS STEEL DISPLACEMENT PUMP Viking Pump, Inc. Model/serial no. LC20S, 107067/a/96 Stainless steel construction 1 inch flanged in and out General data will sell with or without motor setup (1)available

3 inch MODEL 130 WAUKESHA SS DISPLACEMENT PUMP

Stock no. P-2725 3 inch MODEL 130 WAUKESHA SS DISPLACEMENT PUMP Model 130 s/n 251629-99 Sanitary stainless steel 3 inch tri-clamp inlet and outlet sell with or without motor setup (1)available

1 inch GRUNDFOS STAINLESS STEEL MULTI STAGE CENTRIFUGAL PUMP

Stock no. P-2564 1 inch GRUNDFOS STAINLESS STEEL MULTI STAGE CENTRIFUGAL PUMP Grundfos Pumps no. CRN4 60 a-a-a, c-8932 Stainless steel vertical multi-stage pump rated for 300 psi @ 250 deg max, 5 cu. meters/hr.(22 gpm), 68 meters head (223 ft.) 1 inch inlet and outlet Approx. 3 Hp, 208-230/460 volt, 3ph (1)available.

3 inch MODEL 130 WAUKESHA SS DISPLACEMENT PUMP

Stock no. P-2627 3 inch MODEL 130 WAUKESHA SS DISPLACEMENT PUMP Serial no. 14605, model 130 stamped R1-2 Sanitary stainless steel 3 inch threaded with tri-clamp adapters No longer with drive (1)available

7.50 HP FRYMA STAINLESS STEEL COLLOID MILL

Stock no.  C-1212 7.50 HP FRYMA STAINLESS STEEL COLLOID MILL TYPE MZ/80-R, no. 78.1670 1.50 inch stainless steel mill colloid 1.5 inch top in, 1 x 3.5 inch out It is 440 volt, XP, 2 speed motor production rates from 100 to 1000 liters of product per hour ON STAND WITH WHEELS. We may have […]

2.5 x 2 inch FRISTHAM SANITARY STAINLESS STEEL PUMP 20 Hp

Stock Number: P-2710 Fristham 2.5 x 2 inch 316 Sanitary Stainless Steel centrifugal pump Model FP 742-195, serial no. 42174266 20 Hp, 3510 rpm, 230/460v, 3ph, 45.6/27.8 amp 2.5 x 2 inch tri-clamp in /out From a BioPharma operation (1) available

125 GALLON CONE BOTTOM FIBERGLASS TANK

Stock Number: A-4766 125 GALLON CONE BOTTOM FIBERGLASS TANK 28 inch diameter x 3 ft. + cone bottom, bolted lid Steel stand 2 inch bottom outlet, mixer bracket (1) available

1/2 HP CLASSIFIER SEPARATOR DOUBLE WIZZER

Stock Number: B-0685 1/2 HP CLASSIFIER SEPARATOR DOUBLE WIZZER Mfg. Raymond Combustion Engineering Lab Separator, Double Wizzer 1/2 Hp, 3500 rpm, 115/230 v, single phase 2.5 and 2 inch bottom outlets (1) available

CENTRA SCIENTIFIC MODEL 8R REFRIGERATED CENTRIFUGE

Stock Number: F-0182 CENTRA SCIENTIFIC MODEL 8R REFRIGERATED CENTRIFUGE Mfg. Centra Scientific Model 8R, no. 24781330 120v, single phase. To 5900 rpm, 0-34 deg C Uses R12 refrigerant. Takes 750 ml vials Powers up, with manual. Timer 1 to 59 min. (1) available

BECKMAN COULTER LAB CENTRIFUGE

Stock Number: F-0175 BECKMAN COULTER LAB CENTRIFUGE Mfg. Beckman Coulter No. 4480/7860, cat. no. 448003 Array 360 Protein, serology, and Drug System 120/240v, single phase Computerized with keyboard and monitor, missing connection. (1) available

8 inch RO-TAP SIEVE SHAKER SCREENER

Stock Number: C-1408 8 INCH RO-TAP SIEVE SHAKER SCREENER Mfg. W. S. Tyler Inc, no. 12887 1/3 to 1/2 Hp motor to be added Comes with stainless steel sieves/screens 8 inch diameter platform (1) available

10 inch VORTI SIEVE SCREENER RBF-10

Stock Number: C-2241 10 inch VORTI SIEVE SCREENER RBF-10 Mfg. Vorti Siv. Looks like model RBF-10, s/n 10071 10 inch diameter x 1 inch with a cone bottom and lid 3/8 inch tri-clamp top in and bottom out 110v, single phase O/a 14 inch x 22 inch. No screen! Pharmaceutical use. (1) available

3 SQ. FT. SPIRAL HEAT EXCHANGER

Stock Number: G-1871 Mfg. American Heat Reclaming Corp. Type 1-H, no. 15214, 1982, NB 11881 shell = 304 stainless steel, hd = SA515-70 rated for 75 psi @ 200 F (4)3 inch in and out, (2)1 inch drains (1) available

4.25 TON RECIRCULATING HEAT EXCHANGER

Stock Number: G-2620 Mfg. Lepel Type 18310017, model RWWEX-10, s/n 8457 1.5 Hp, 208 volt, 1 ph, 4.5 a, 15Kw, 51,225 Btu/Hr Gauge to 140 F/60 C, 100 psi 15.5 in. x 8 in. x 18 in. reservoir, 10 gallon Brass 1 in. water in and out, 1.5 in. process in and out (1) available

21 CU. FT. STAINLESS STEEL DOUBLE CONE VACUUM DRYER-BLENDER

Stock Number: D-1083 21 CU. FT. STAINLESS STEEL DOUBLE CONE VACUUM DRYER-BLENDER Mfg. PAUL O. ABBE, INC. Serial no. A40755, RotoCone, maximum bulk density of 150 lbs./cu. ft. 32 cu. ft. total. Working volume 65% fill level is 21 cu. ft. 1.5 Hp gear motor for drive, 5 rpm drum speed, 5 Hp 1165 rpm for […]

1/4 HP VERTICAL DOWN MIXER

Stock Number: B-3327 Mfg. Lightnin Vektor model VST18N 1/4 Hp, 1725 rpm, 230/460v, 3ph Flange mount with stainless steel face Sell with or without shaft and prop (1) available

1/4 Hp LIGHTNIN VEKTOR CLAMP MOUNT MIXER high speed

Stock Number: B-3563 1/4 Hp LIGHTNIN VEKTOR CLAMP MOUNT MIXER high speed Mfg. Lightnin Vektor model V1P18N 1/4 Hp, 1725 rpm, 230/460 v, 3ph High speed stainless steel shaft made to order and prop included Several similar mixers available!! (1) available

1/4 HP LIGHTNIN VEKTOR CLAMP MOUNT MIXER

Stock Number: B-2276 1/4 HP LIGHTNIN VEKTOR CLAMP MOUNT MIXER Mfg. Lightnin Vektor model V6P18 1/4 Hp, 1740 rpm, 208-230/460 v, 3ph gear reduced stainless steel shaft made to order and prop included (1) available

.33 HP LIGHTNIN VEKTOR CLAMP MOUNT MIXER 115/230 v

Stock Number: B-3564 (2) .33 HP LIGHTNIN VEKTOR CLAMP MOUNT MIXER 115/230 v Mfg. Lightnin Vektor model V5P25 1/3 Hp, 115/230 v, 1 ph gear reduced stainless steel shaft made  to order and prop included (2) available

1/2 HP VERTICAL DOWN LIGHTNIN MIXER

Stock Number: B-3349 1/2 HP VERTICAL DOWN LIGHTNIN MIXER Mfg. Lightnin Vektor model VIT37 1/2 Hp, 1720 rpm input, high speed, 230/460v, 3ph 10 inch flange mount with mechanical seal for 1″ diameter shaft (1) available

1 HP VERTICAL DOWN MIXER

Stock Number: B-2856 Mfg. Lightnin Model XLSS 100A, no. 91/A56743 Gear reduced, estimated shaft speed 690 at 3450 rpm 1 Hp, 3450/2050 rpm, 208-230/460v, 3ph, xp 4 bolt mount, 6-bolt flange for shaft mount (1) available

1 inch PALL FILTRON MAXIMATE TANGENTIAL FLOW FILTER

Stock Number: C-2469 1 inch PALL FILTRON MAXIMATE TANGENTIAL FLOW FILTER Mfg. Pall Filtration Maximate Tangential Flow Cassettes, no. 22074.01 (2) 1 inch and (2) 1/2 inch tri-clamp inlets and outlets Membranes measure 2.5 inch x 13 inch x 1 inch thick Overall measurements 14 inch x 7 inch x 14.25 inch (1) available

1 HP NETTCO VERTICAL DOWN MIXER

Stock Number: B-2901 1 HP NETTCO VERTICAL DOWN MIXER Mfg. Nettco Corp Model NSGF-100 1 Hp, 1140 rpm, 230/460 v, 3ph gear reduced (1) available

4 inch X 12 inch STAINLESS STEEL BASKET BAG FILTER

Stock Number: C-2211 4 inch X 12 inch STAINLESS STEEL BASKET BAG FILTER Mfg. Ronningen-Petter, serial nos. S06148 and S06149 Rated for 300 psi @ 220 deg. F Twin 316L ss housings 2 inch inlet and outlet, 4.5 x 12 inch baskets Will clean before shipping. Selling as pair! MISSING BASKETS (1) available

20 inch x 7 cartridge 316 STAINLESS STEEL FILTER US FILTER

Stock No. C-2287 (2) 20 inch x 7 cartridge 316 STAINLESS STEEL FILTER US FILTER Mfg. US Filters, takes (7) slip in type cartridges Model T910596-300, Type 14MEGA+2-2 Rated for 150 psi @ 200 deg. F 9 inch diameter x 26 inch with dished bottom Clamped dished top, 2 inch side in & out 3/4 […]

50 GALLON STAINLESS STEEL NEUTSCH TYPE FILTER

Stock Number: C-1749 22 inch diameter x 31 inch on a 24 x 28 inch cart Fine screen, coarse screen, and bottom grate 1 inch bottom center to side outlet Housing clamps to bottom, open top (1) available

1200 mm NETZSCH KLICO FILTER PRESS RECESSED PLATES

Stock Number: C-CD01 (130) 1200 mm NETZSCH KLICO FILTER PRESS RECESSED PLATES From Netzsch Model 1200/61-67 filter presses 1200 mm recessed non-gasketed poly plates, 6 in. center feed Priced for a set of 65 that include front and rear head plates WILL SELL INDIVIDUAL PLATES. HEAD PLATES ONLY COME WITH A COMPLETE SET OPEN TO […]

1200 MM RECESSED GASKETED FILTER PRESS PLATES (33)

1,200 MM  RECESSED GASKETED FILTER PRESS PLATES Stock No. C-2158 Recessed and gasketed 1200 mm poly filter plates, 47 inch square (33) recessed and gasketed poly plates, (29) with spickets (4) 2 inch corner in and out came from a Sperry Filter Press Will consider selling individually (33) available

1 HP MICRO PULVERIZER GRINDER PARTS

Stock Number: C-1316 1 HP MICRO PULVERIZER GRINDER PARTS Mfg. HOSOKAWA MICRON POWDER SYSTEMS( MIKROPUL) TYPE SH, S/n 80J-5274 2 in. top inlet, 1.5 in. x 7 in. bottom outlet SS fill funnel 1 HP, 3450 RPM, 3 PH PLEASE NOTE THIS GRINDER IS CURRENTLY MISSING THE HAMMER SETUP (1) available

1.74 HP LIGHTNIN VERTICAL DOWN MIXER

Stock Number: B-3684 1.74 Hp Lightnin vertical down mixer gear reduced 1.74 Hp, 230/460 v, UL listed Group I Hazards Model XJSS-174, serial no. 92-B00685 gear reduced, 350 rpm output We can make up stainless steel shaft to order and supply with a prop (1) available

7 .5 HP NORD GEAR MOTOR INLINE

Stock Number: B-3286 7 .5 HP NORD GEAR MOTOR INLINE Mfg. Nord Gear Corp. 2006208910963 7.5 Hp, 1735 rpm, 3ph 5.50 ratio, 318 rpm output (1) available

1 INCH G & L MULTI STAGE STAINLESS STEEL CENTRIFUGAL PUMP

Stock Number: P-2297 1 INCH G & L MULTI STAGE STAINLESS STEEL CENTRIFUGAL PUMP Mfg. G & L Pump div. of ITT Goulds Model SSV 1SVOK4 1 Hp, 3450 rpm, 230/460v, 3ph Stainless Steel contacts Rated for 360 psi @ 250 deg. F Includes Aquavar 56 controller (1) available

1 inch GRUNDFOS SS MULTI-STAGE CENTRIFUGAL PUMP

Stock Number: P-2562 1 inch GRUNDFOS SS MULTI-STAGE CENTRIFUGAL PUMP Grundfos stainless steel multi-stage pump Model CR4, NH-C5-60, 9046 Rated for 300 psi @ 250 deg. F 3 Hp, 3450 rpm 208-230/460 v, 3ph 1 inch in & out. Stainless Steel (1) available

1.5 X 2.5 INCH SUMP PUMP TURBINE TRANSFER

Stock Number: P-0557 Mfg. Vortex – Lawrence Pump Model 1 1/2 x 2 1/2, assy. 05806, s/n 31879 7.5 Hp, 1740 rpm, 3ph motor 2.5 inch inlet, 1.5 inch outlet Rated for 30 gpm, 80 ft. hd.. 10 ft. depth Mounted on 24 inch diameter manway cover (1) available

2 X 1.25 INCH STAINLESS STEEL CENTRIFUGAL PUMP

Stock Number: P-1830 2 X 1.25 INCH STAINLESS STEEL CENTRIFUGAL PUMP Mfg. G & L Pumps div. of ITT/Goulds Model SST 5 Hp, 1730 rpm, 208-230/460v, 3ph 2 x 1.25 inch with 9 3/4″ impeller (1) available

2 X 2.5 inch FRISTHAM SANITARY SS CENTRIFUGAL PUMP 15 Hp

Stock Number: P-2182 2 x 2.5 inch FRISTHAM SANITARY SS CENTRIFUGAL PUMP Mfg. Fristham Pumps Model FP 742-205, s/n FP74296696 15 Hp, 3450 rpm, 208-230/460v, 3ph 2 x 2.5 inch in and out, 1/4 inch drain rated for 110 gpm, 260 ft. hd. (1) available

3 X 1.5 INCH INGERSOLL RAND CENTRIFUGAL PUMP

Stock Number: P-2178 3 X 1.5 INCH INGERSOLL RAND CENTRIFUGAL PUMP Mfg. Ingersoll Rand 3×1.5x8HOC Stainless steel Rated for 150 gpm, 200 ft. hd., 350 psi @ 3500 rpm 3 inch x 1.5 inch in and out Sell with or without motor setup (1) available

FLOWTECH 1.5 INCH UNIBLOC STAINLESS STEEL DISPLACEMENT PUMP 350

Stock Number: P-2025 1.5 INCH UNIBLOC STAINLESS STEEL DISPLACEMENT PUMP Flowtech Unibloc ss displacement pump Model Labtop 350, no. 3987 1.5 inch tri-clamp in and out, 316 Sanitary Stainless steel 15 amp, 115v, speed control with reverse Pump and motor works. Problem with digital controls. Can setup with motor and gear reducer. (1) available

1/4 INCH METERING PUMP FMI FLUID METERING INC

Stock Number: P-2044 1/4 INCH METERING PUMP FMI Mfg. FMI Fluid Metering Inc. Model VO6231AD11 Rated 0 to 12 ML per min., 100 psi max .96 amp, 115v, 1ph, 60hz Stainless steel with ceramic piston 1/4 inch in and out (4) available

1/4 HP LAB VACUUM PUMP

Stock Number: P-2299 Fisher Scientific Speed Aire 4Z335-0690 1/4 Hp, 1725 rpm, 115v, 1ph 1/4 inch in and out We also have a similar 1/3 Hp and 1/6 Hp (1) available

3/4″ PNEUMATIC PISTON PUMP DRUM PUMP

Stock Number: P-2189 3/4″ PNEUMATIC PISTON PUMP DRUM PUMP Mfg. Wyandotte No. E-261, 5-10, 22627 3/4 inch in and out Air powered Buy with or without ss cart (1) available

17 cfm GAST ROTARY VANE VACUUM PUMP

Stock Number: P-2301 17 cfm GAST ROTARY VANE VACUUM PUMP Mfg. Gast Model 2065-V2A, rated to 17 cfm, 25 psi, 28 inches Hg Has 3/4 inch in and out Labeled rebuilt (1) available

5 Hp WEBTROL STAINLESS STEEL BOOSTER PUMP EZ SERIES

Stock Number: P-2214 5 Hp WEBTROL STAINLESS STEEL BOOSTER PUMP Mfg. Webtrol Pumps, model H20B15-1S16 3PH, code 5/90 EZ Series Booster Pump. UNUSED!! Still in crate! 5 Hp, 3500/2900 RPM, 208-230/460 v, 60/50 hz, 3ph 1.75 inch in & out. 3.5 inch diameter barrel x 26 inch O/a 11 x 41 x 11 inches Stainless […]

3 GPM GRACO PNEUMATIC PISTON PUMP

Stock Number: P-1924 3 GPM GRACO AIR OPERATED POWER WASHER PUMP Mfg Graco Pump Model IGF Hydra Clean Rated for 3 gpm Power washer application For more info, visit the following page: http://www.graco.com/Internet/T_PDB.nsf/SearchView/Hydra-Clean (1) available

5 HP HYDRAULIC PUMP SYSTEM

Stock Number: P-1121 Mfg. Lincoln Controls Hydraulic Systems Double A pump Model PVV-06-10A2 5 Hp, 208-230/460v, 3ph Control switch, oil resevoir, temp. guage. ONE AVAILABLE! (1) available

8 HP LINK BELT GEAR REDUCER INLINE

Stock Number: B-3083 Mfg. Link Belt Model 2947Y130U, size 5DTB-2 38.4 ratio, rated fpr 8.44 Hp, class 2 7/8 x 2 inch input shaft, 2.5 x 5 inch output shaft (1) available

30 GALLON FIBERGLASS TANK

Stock Number: A-2570 30 gallon dished bottom fiberglass tank 20 inch id x 24 inch with hinged lid, (3)legs Mfg. Palmer Fiberglass, no. FC-8404 Last used for Sodium Hydroxide 10% 2 inch bottom center outlet, ass’t top inlets (1) available

70 GALLON FIBERGLASS TANK

Stock Number: A-2794 24 inch diameter x 36 inch, flat bottom & top Hinged lid (3)2 inch side in and out 6 inch & (4) 2 inch top inlets in lid (1) available

110 GALLON FIBERGLASS TANK with DISHED BOTTOM and TOP

Stock Number: A-2872 110 GALLON FIBERGLASS TANK with DISHED BOTTOM and TOP Mfg. FI Company, 5/90 Rated to 5 psi pressure Derakane 470 resin 3 ft. x 2 ft. w/ dished top and bottom 1.8 in. bottom center outlet, 18 in. tmw. On wheels. 3 in. and (4)1.5 in. top in. Flange to mount mixer. […]

200 gallon FIBERGLASS TANK FLAT BOTTOM with METERING PUMPS

Stock Number: A-4057 200 gallon FIBERGLASS TANK FLAT BOTTOM with METERING PUMPS Mfg. NE Plastic Coated Products 3 ft. x 45 in., flat bottom and top w/lid 1 inch side outlet, 1.5 inch top inlet Ultra sonic level control, skid mounted With  N-feeder solenoid type metering pumps Used with Sulfuric acid solution (1) available

250 GALLON FIBERGLASS TANK

Stock Number: A-4670 250 GALLON FIBERGLASS TANK 46 inch diameter x 3 ft. flat bottom, open top 1 & 3 inch side outlets, 2 inch side inlet Internal baffle (1) available

360 gallon FIBERGLASS TANK with Dished Bottom

Stock Number: A-2748 (4) 360 gallon FIBERGLASS TANK with Dished Bottom Mfg. Beetle Plastics 38 inch diameter x 86 inch with dished bottom Open top with bolt holes on rim, A couple with lids. 180 deg. F design temperature 2 inch and 3 inch bottom center outlets available!! (4) baffles (4) available

550 GALLON POLY TANK

Stock Number: A-4627 550 GALLON POLY TANK 52 inch diameter x 5 ft. deep, flat bottom, open top 1 inch and 2 inch side outlets (1) available

550 GALLON FIBERGLASS TANK DISHED BOTTOM

Stock Number: A-3810 550 GALLON FIBERGLASS TANK DISHED BOTTOM 4 ft. diameter x 70 inch + dished bottom & top 21 inch top center manway 2 inch bottom center outlet, 1.5 inch top inlet Came out of a pickle plant (1) available

658 GALLON FIBERGLASS FILTER TANK with MANIFOLD

Stock Number: A-1952 (2) 658 GALLON FIBERGLASS FILTER TANK with MANIFOLD 4 ft. diameter x 7 ft. with 10 inch domed lid top manway, 3 inch top inlet 2.5 inch side inlet & outlet, (2)2 inch side outlets Has packed internals with PVC manifold (2) available

700 GALLON FIBERGLASS TANK

Stock Number: A-4628 54 inch diameter x 70 inches deep, flat bottom (4) baffles, open top (2) 1.5 inch side outlets, (3) 1 inch side inlets (1) available

725 GALLON FIBERGLASS TANK

Stock Number: A-2388 64 inch diameter x 52 inch with 11 inch cone bottom Open top 2 inch bottom center outlet that needs repair Legs need repair as well. Selling AS IS! (1) available

2,500 GALLON FIBERGLASS TANK

Stock Number: A-1945 7 ft. diameter x 101 inch straight side 7 inch dished top and flat bottom Needs repair on bottom, can see light coming through Selling AS IS! (1) available

4400 GALLON FIBERGLASS TANK with COILS

Stock Number: A-1908 4400 GALLON FIBERGLASS TANK with COILS 8 ft. diameter x 11 ft. Flat top & bottom 24 inch side and top manways 2 inch side outlet Has coils inside for heating or cooling Partially Insulated Needs work, selling “AS IS”, Reduced! (1) available

8000 GALLON FIBERGLASS TANK

Stock Number: A-4277 8000 GALLON FIBERGLASS TANK Mfg. Owens Corning Model 108MC, no. 6088-596 10 ft. diameter x 14 ft with closed top and flat bottom 22 inch side and top manways, 2 inch side outlet 2.5 inch top vent, 1 and (2) 2 inch top inlets. 3 inch dip tube Has some stress cracks […]

55 gallon XP DRUM BARREL DUMPER ELECTRIC

Stock Number: G-1518 55 gallon XP DRUM BARREL DUMPER ELECTRIC Heavy construction, approx. 55 inch lift 1 hp hydraulic pump 3 ph, XP motor Pneumatic-controlled valve 44 x 52 x 86 inch tall (1) available

2000 LBS LEXCO PLATFORM LIFT TABLE

Stock Number: G-2283 2000 LBS LEXCO PLATFORM LIFT TABLE Mfg. Lexco Model HT-2338-2F 20 x 30 inch top, 30 inch tall in down position 46 inch in up position Foot pump hydraulic lift Has 20 x 20.5 x 12 inch tall galvanized box that can be removed (1) available

2.5 GALLON STAINLESS STEEL PRESSURE TANK

Stock Number: E-3460 Mfg. Alloy Products Corp. Rated for 130 psi @ 9 x 7 inch with dished top and bottom 5 x 6 inch top port. (4) 3/8 inch top inlets NO LONGER WITH A LID but they are available from other sources (1) available

3.5 GALLON STAINLESS STEEL PRESSURE TANK

Stock Number: E-3778 (42) Mfg. Alloy Products Corp 9 inch diameter x 12 inch + dished bottom & top Rated for 120 psi @ 100 deg. F 2 inch top threaded (npt) center fitting (have one with a cap) (4) 3/4 inch tri-clamp top fittings. No bottom outlet (42) available

4 GALLON STAINLESS STEEL PRESSURE TANK

Stock Number: E-3471 Mfg. Alloy Products Corp. Rated for 130 psi @ 100 deg. F 9 inch diameter x 14 inch with dished top and bottom 5 x 6 inch oval top port, (4) 3/8 inch top in Dip tube, no bottom outlet. Rubber base 316L sanitary stainless steel. NO LONGER WITH A LID but […]

4.5 GALLON 316L STAINLESS STEEL PRESSURE TANK

Stock Number: E-3834 (8) 4.5 GALLON STAINLESS STEEL PRESSURE TANK Mfg. Alloy Products, 316L stainless steel Rated to 140 psi @ 100 deg. F 9 inch x 16 inch (approx.) Small oval top port and (4) 1/4″ NPT threaded top fittings No bottom outlets (8) available, pressures 130 to 155 psi available

4.5 gallon 316L STAINLESS STEEL PRESSURE TANK

Stock Number: E-3862 (2) 4.5 gallon 316L STAINLESS STEEL PRESSURE TANK Mfg. Alloy Products Rated for 100 psi @ 100 deg. F 316L stainless steel with rubber base 9 inch diameter x 16 inch + dished top & bottom (2)1/2 and (2)1/4 inch NPT top inlets, 4 x 6 inch top port No bottom outlet […]

13 gallon 316L STAINLESS STEEL PRESSURE TANK

Stock Number: E-3830 (2) 13 gallon 316L STAINLESS STEEL PRESSURE TANK Mfg. Alloy Products Rated 115 psi @ 100 deg. F 12 inch x 28 inch, 13 gallon/50 liter capacity (4) 1/4 inch NPT threaded top inlets 5 x 6 inch top center port. No outlet 316L stainless steel (2) available

200 gallon FIBERGLASS REINFORCED POLY PRESSURE FILTER TANK 

Stock Number: E-3715 200 gallon FIBERGLASS REINFORCED POLY PRESSURE FILTER TANK Mfg. Pentair , Structural North America 28 inch diameter x 54 inch + dished top & bottom Rated for 150 psi @ 150 deg. F 1.5 inch in and out. O/a 30 inch diameter x 84 inch tall For water filtration. Has filter media. […]

10 gallon STAINLESS STEEL STEAM JACKETED TILT KETTLE

Stock No. E-2263 10 gallon STAINLESS STEEL STEAM JACKETED TILT KETTLE Mfg. Cleveland Range Co. 17 inch diameter x 13 inch deep Model KDT-10T, NB stamped Jacket rated for 50 psi @ 298 deg. F Tilt with sink base (1) available

0.65 GALLON STAINLESS STEEL JACKETED PRESSURE TANK

Stock Number: E-3886 0.65 GALLON STAINLESS STEEL JACKETED PRESSURE TANK Mfg. Acme Industrial Shell = FV/110 psi, jkt. = 80 psi @ 325 deg. F Marked 1.7 liter, total capacity = .65 gallon 4.75 inch id x 8.5 inch deep, flat bottom Clamped flat top with dip tube (1) available

1.2 GALLON STAINLESS STEEL JACKETED PRESSURE TANK

Stock Number: E-3885 1.2 GALLON STAINLESS STEEL JACKETED PRESSURE TANK Mfg. Acme Industrial Shell= FV/110 psi, jkt.= 80 psi @ 325 deg. F Marked 4 liter capacity, Total volume = 1.20 gallon 4.75 inch id x 15.75 inch, flat bottom, no outlet Has clamped flat top with dip tube (1) available

8 inch Dezurik Knife Valve

Stock Number: G-2799 Dezurik 8″ diameter knife valve, 304 SS contacts Pneumatic control stamped 9067786 8 bolt holes, 11.5in. center to center (1) available

900 PSI Magnetic Level Gauge

Stock Number: G-2614 Mfg. K-Tek Corp. Rated for FV/900 psi, 150 to 325 F 1.0 specific gravity 316 stainless steel 3/4 in. side inlet and outlet 3 inch diameter x 52 inch ss housing (1) available

2.5 gallon 304L STAINLESS STEEL TANK

Stock Number: A-2756 2.5 gallon 304L STAINLESS STEEL TANK 8 inch diameter x 10 inch with dished bottom, flat top 304L stainless steel heavy gauge (4)baffles and agitator 2.5 inch top center inlet,(2)2 inch top inlets 1/4 inch top inlet, 1 inch bottom side outlet (1) available

2 LITER STAINLESS STEEL REACTOR 750 PSI

Stock Number: E-1769 (2) 2 LITER STAINLESS STEEL REACTOR 750 PSI Mfg. KIRKWOOD FABRICATORS S/N 7-206-2 (OR 3) 1987, N.B. 584 (or 585) 400 Stainless steel 500 PSI @ 302 DEG. F TEST 750 PSI 3 in. X 12 in. O/A 24 in. X 13 in. X 76 in. HONEYWELL 1/4 HP 2500 RPM, MAGNA […]

10 GALLON GLASS LINED TANK with MIXER

Stock Number: A-2375 10 GALLON GLASS LINED TANK with MIXER Glass lined carbon steel tank, stainless steel 3 pc. lid 13 in. x 16 in., dished bottom 1/4 Hp, 230/460 v, 3 ph Mixer with Teflon coated shaft 1.5 in. bottom center outlet (3)18 in. legs on ss platform (1) available

2.5 LITER HASTELLOY C REACTOR 350 PSI

Stock Number: E-1771 (2) 2.5 LITER HASTELLOY C REACTOR 350 PSI Mfg. NOOTER CORP. Serial no. NO. D-1616-2 1985, N.B. 11486 304 S/S HD HASTELLOY C SHELL 350 PSI @ 302 DEG. F HONEYWELL 1/4 HP 2500 RPM, MAGNA DRIVE II 5 in. dia. x 10 in. deep (2) available SALE PENDING  

12 GALLON STAINLESS STEEL TANK

Stock Number: A-4428 Stainless Steel Tank 12 gallon 12 inch diameter x 24 inch with cone bottom Open top with gasket (missing lid) (4) 1/2 inch and (5) 1,5 inch side in and out Sanitary tri-clamp fittings, 1/2 inch bottom outlet SS skid mounted with cannibalized electrical box (1) available

5 gallon STAINLESS STEEL REACTOR 400 psi

Stock Number: E-1956 5 gallon STAINLESS STEEL REACTOR 400 psi Mfg. Proctor and Gamble S/n PV8145-1, NB 2, 1981, rerated in 1990 Shell 400 psi @ 500 deg. F, 171 psi jacket 12 inch x 18 inch, dished bottom, flat top Sell with or without a mixer Stainless steel shell, carbon steel jacket (1) available

5 gallon 316 STAINLESS STEEL REACTOR 350 psi

Stock Number: E-2055 5 gallon 316 STAINLESS STEEL REACTOR 350 psi Mfg. G H Hicks div. of Chemineer no. 11741-24121, 1974, NB 925 Shell = 350 psi @ 500 F, jkt.= 150 psi Ribbon type scrape agitator 316 stainless steel shell, carbon steel jacket 14 inch diameter x 13 inch, dished bottom, flat top (1) […]

15 GALLON STAINLESS STEEL TANK

Stock Number: A-2426 15 GALLON STAINLESS STEEL TANK 18 inch diameter x 14 inch w/ dished bottom. Bolted flat top Has 2 Hp mixer, 1730 rpm, 60-1 gear reduced 4 inch bottom out, (2) top sight glass and several inlets Legs can be modified Sell with or without mixer (1) available

40 GALLON 316 STAINLESS STEEL TANK with MIXER

Stock Number: A-2768 40 GALLON 316 STAINLESS STEEL TANK with MIXER Mfg. DCI, Inc (Dairy Craft Inc.) Serial no. 92-PH-44148-A 23 in. x 24 in., dished bottom, flat top Has 1/2 Hp Eurodrive agitator, 230/460 v, 3ph 316 Sanitary stainless steel. 1 in. tri-clamp outlet Internal baffle, hinged lid, polished!. Comes with an electric heating […]

300 GALLON STAINLESS STEEL TANK DISHED BOTTOM

Stock No. A-5401 300 GALLON STAINLESS STEEL TANK 44 inch diameter x 42 inch with dished top and bottom Stainless steel, insulation has been stripped off 1 inch bottom center outlet, 1 inch side inlet and outlet Top inlets = 2, 4, and (4)1 inch (1) available